Bosch Dishwasher E24 Error: Drain Problem Fix

Quick answer

A Bosch dishwasher E24 error means it is not draining properly, usually because the filter is blocked. Bosch also lists a kinked or blocked drain hose, a loose pump cover and a knockout plug left in a new garbage disposal. Clear the cause, then reset the dishwasher by cutting power for about a minute.

Standing water and an E24 on the display look serious, but this is one of the most fixable Bosch codes. The Bosch dishwasher E24 error is the machine telling you the water cannot get out fast enough. Usually it is food in the filter or a kinked hose, and you can check every common cause in under an hour.

What the E24 error means

Bosch’s E24 page says the dishwasher “is not draining properly due to the drain filter being blocked.” Bosch lists three signs that come with it: water pooling after a cycle, the dishwasher pausing or stopping mid-cycle, and gurgling or humming noises.

E24 has a close relative. On the Bosch error code list, E25 means the drain pump is blocked or the pump cover is loose or missing. The fixes overlap, so this guide covers both.

CodeWhat Bosch saysWhere to look first
E24Not draining properly; drain filter blockedFilter, drain hose, disposer plug, pump cover
E25Drain pump blocked, or pump cover loose or missingPump under the filter, pump cover

Causes of the E24 error

#CauseWho says soDifficulty
1Blocked or dirty filterBoschEasy
2Kinked or blocked drain hoseBoschEasy–Medium
3Knockout plug left in a new garbage disposalBoschEasy
4Loose pump coverBoschEasy
5Debris in the drain pump (more often E25)BoschMedium
6Siphon connection not sealedBoschMedium
7Clogged kitchen drain or air gapOur own additionEasy–Medium
8Failed drain pumpOur own additionHard

Safety first

Switch the dishwasher off and turn off the power at the circuit breaker before you reach into the sump, as Bosch advises for its resets. Wear gloves: Bosch warns that some debris in the pump area may be sharp, and broken glass often ends up there. The water in the tub and the hose may be hot, so give it time to cool.

Step 1: Remove the standing water

You cannot see the filter under a pool of dirty water.

  1. Cut power at the breaker and put towels on the floor.
  2. Scoop the water out with a small bowl, then soak up the rest with a sponge. This is our own method; Bosch describes using a sponge to remove standing water from the pump area.

Step 2: Clean the filter

Bosch names a blocked filter as the main cause of E24.

  1. Remove the bottom rack.
  2. Take the filter out as your owner’s manual shows. On most Bosch models it twists and lifts out.
  3. Bosch’s not draining page says to remove any trapped debris and wash the filter with soap and a soft brush under running water.
  4. Put it back so it locks firmly in place.

Our full dishwasher filter cleaning guide walks through the Bosch design part by part.

Step 3: Check the pump cover and the pump

The pump cover sits under the filter. Bosch says it may be loose, and for E25 it may be missing or the pump may be blocked.

  1. With the filter out, look at the pump cover. Your manual shows where it is.
  2. Make sure it is seated and not loose.
  3. If the pump is blocked, the Bosch error code page says to pry off the cover with a spoon until it clicks, then remove debris and standing water with a sponge.
  4. Look for glass, bones, fruit seeds and labels. Remove them carefully.
  5. Clip the cover back on, then refit the filter.

Step 4: Check the hoses

  1. Pull out the bottom kick panel or look under the sink to follow the drain hose.
  2. Bosch says to check that the inlet hose is not kinked or damaged.
  3. Check the drain hose along its whole length. Bosch lists a blocked drain hose as a cause. A dishwasher pushed back hard against the wall often crushes it.
  4. Bosch says to confirm that the siphon connection, where the hose joins the sink drain, is sealed.

Step 5: Check the garbage disposal connection

This is the classic cause of an E24 on a new installation. A new disposer comes with a knockout plug sealing its dishwasher inlet. Bosch says the installer may have forgotten to remove it, and that if the drain hose connects to a disposer, you should remove the plug from the disposer’s dishwasher drain connection.

  1. Turn off the disposal at the breaker and disconnect the dishwasher hose.
  2. If the inlet is closed with a solid disc, the plug is still in. Knock it out following the disposer’s instructions, remove it from inside and reconnect the hose.

Also run the disposal for a few seconds before you start the dishwasher. A full disposer can back water up into the dishwasher. That tip is ours.

Step 6: Reset the dishwasher

Bosch says to reset the dishwasher and the error code according to your owner’s manual after fixing the cause. The general reset on its error code page is:

  1. Turn the dishwasher off, or switch off the power at the breaker.
  2. Wait about 1 minute.
  3. Turn the power back on.
  4. Run a short test cycle with no dishes.

For many codes, Bosch also suggests resetting the breaker for 30 seconds. If the tub is empty at the end, the drain works.

If the E24 comes back

If the code returns after a clean filter, a clear pump, straight hoses and a reset, check the kitchen sink drain: if the sink itself drains slowly, the dishwasher has nowhere to send its water. Our dishwasher not draining guide covers the sink, air gap and high loop checks that apply to every brand. The same logic applies to washing machines; see our washer not draining guide.

If everything is clear and E24 persists, the drain pump may have failed. Bosch says to contact Bosch Customer Service at 1-800-944-2904. If the dishwasher is out of warranty and older, weigh the quote with the 50% rule in our repair or replace guide.

Once a month, open the door at the end of a cycle and look at the bottom of the tub. A little moisture is normal; a pool of water is an early warning that the filter needs cleaning. This is our own habit.

Bosch E24 Error? FAQ

What does E24 mean on a Bosch dishwasher?

Bosch says E24 means the dishwasher is not draining properly because the drain filter is blocked. Other causes include a blocked drain hose, a loose pump cover and a disposer knockout plug.

How do I fix the E24 error?

Clean the filter, check the pump cover, straighten the inlet and drain hoses, confirm the siphon connection is sealed and remove any disposer plug. Then reset the dishwasher as your manual describes.

How do I reset a Bosch dishwasher?

Bosch’s general reset is to turn the dishwasher off or switch off the breaker, wait about a minute, turn it back on and run a short test cycle with no dishes.

How do I get water out of a Bosch dishwasher that won’t drain?

Turn off the power, scoop the water out with a bowl and soak up the rest with a sponge. Then clean the filter and pump area, which is where Bosch says debris usually causes the blockage.

What is the difference between E24 and E25?

Bosch says E24 means the dishwasher is not draining properly because the filter is blocked. E25 means the drain pump is blocked or the pump cover is loose or missing.

Sources