Dryer Vent Hose and Duct: Which Type Is Safe and How to Install It

Quick answer

The safest dryer vent hose is 4-inch rigid metal duct, with a short stiff-walled flexible metal connector only where needed. Skip plastic and thin foil accordion hose. Keep a short run with few elbows, join sections without screws and vent it outdoors.

The dryer vent hose behind your machine carries hot, damp, lint-laden air outdoors. The U.S. Consumer Product Safety Commission says plastic or foil accordion duct traps lint more easily and is prone to kinks that greatly reduce airflow. If your duct is the right type and just full of lint, use our step-by-step dryer vent cleaning guide instead.

Which dryer vent hose types are safe?

Duct typeVerdictWhy
Rigid metal (aluminum or galvanized steel)Best choiceSmooth inside, does not crush, the type most makers specify
Semi-rigid corrugated metalOK for the short connectorHolds its shape; CPSC lists it with rigid duct
Stiff-walled flexible metalOK, short and visible onlySamsung and Whirlpool accept it with limits
Thin foil accordion hoseAvoidCrushes, sags and catches lint
Plastic or vinyl hoseNeverCPSC, Samsung, LG and Whirlpool all advise against it

Samsung’s dryer setup page asks for a 4 inch diameter rigid aluminum or galvanized steel duct and says not to use flexible plastic. Whirlpool recommends rigid or flexible metal and says only 4-inch heavy metal vent should be used, because a larger or smaller size slows airflow and drying. LG also says to avoid plastic or vinyl ducting. The NFPA safety sheet also calls for rigid or flexible metal.

Safety first

Unplug the dryer before you move it. On a gas dryer, shut the gas valve and do not kink or strain the gas line; if you smell gas, leave the house and call your gas utility. Samsung recommends a professional installer if you are putting in a duct for the first time, and NFPA says to have the dryer installed by a professional.

How to install a dryer vent duct

  1. Measure the route. Note the distance to the wall pipe or outside hood and count every bend.
  2. Buy the parts. Get 4-inch rigid metal pipe and elbows for the main run, a short semi-rigid metal connector (no foil), two clamps and metal foil tape. Check that the hood flap swings freely.
  3. Remove the old hose. Pull the dryer out, loosen the clamps and take off any plastic or foil hose. Vacuum the outlet and wall pipe.
  4. Fit the rigid run first. Slide each rigid section into the next one in the direction of airflow. Do not drive screws into the duct: Samsung’s manual says fasteners that extend into the duct catch lint.
  5. Attach the connector. Clamp the short metal connector to the dryer outlet and to the wall pipe. Stretch it out fully and cut off any extra length so it cannot sag.
  6. Push the dryer back gently. Samsung asks for at least 4 inches of clearance so the duct is not crushed.
  7. Test it. Run the dryer and check outside that air blows out and the flap opens, as the CPSC advises.

How long can a dryer vent duct be?

LG’s venting page gives these limits for 4-inch rigid metal duct with its recommended wall cap. Your own manual’s chart rules for your model.

90° elbowsLG maximum length
065 ft
155 ft
247 ft
336 ft
428 ft

LG says not to use more than four 90° elbows. For the flexible part, Samsung’s manual sets a total of no more than 7 ft 10½ in (2.4 m). Whirlpool wants the run as straight and short as possible, with the hood at least 12 inches above the ground.

Tape, clamps or screws: what holds the joints?

Samsung’s setup page allows hose clamps or duct tape at the dryer and wall vent, and its manual bans screws that reach inside. Our own choice is clamps at both ends and aluminum foil tape on rigid seams, since cloth duct tape dries out with heat.

Where must the duct end?

Outdoors. Samsung’s manual says the dryer must not exhaust into a chimney, wall, ceiling, attic, crawl space or other concealed space of the building. Our rule: any section hidden inside a wall or ceiling should be rigid metal, since you cannot see it crush or sag. Slow drying has other causes too, covered in our guide to a dryer taking too long to dry; a dryer that cuts out is in our dryer shuts off guide. While you are in the laundry room, see how to clean a front load washer.

After the new duct is in, Samsung owners can run the built-in Vent Blockage Test; the manual says to run it while the dryer is cool. Writing the install date on tape on the duct is our own tip for timing the next cleaning.

Pick a Safe Dryer Vent Duct FAQ

Is a foil dryer vent hose safe?

Not as a rule. The CPSC says to replace foil accordion duct with rigid or semi-rigid metal. Samsung’s manual allows foil only if the maker identifies it for that dryer and it meets UL Subject 2158A.

What size dryer vent hose do I need?

Most dryers need 4 inches. Samsung and Whirlpool both specify 4-inch metal; Whirlpool adds that other sizes slow drying.

Can a dryer vent hose go through a wall or ceiling?

It can pass through to the outside, but it must not end there. Samsung’s manual says not to exhaust into a wall, ceiling, attic or concealed space.

Can I vent a dryer indoors?

Not a vented dryer. Samsung’s manual says all dryers in the US and Canada must be exhausted outside, not into an attic or chimney.

How many elbows can a dryer vent have?

LG allows four 90° elbows at most; its chart drops from 65 ft with none to 28 ft with four.

Sources