Quick answer
To clean a dryer vent, unplug the dryer, pull it out and disconnect the duct. Run a vent brush kit through the duct from inside and from the outside hood, vacuum the lint, reconnect, then check that air blows out strongly. NFPA says to do it at least once a year.
Some lint always gets past the screen and settles in the duct. The U.S. Consumer Product Safety Commission warns that lint in the dryer or the exhaust duct can block the airflow, cause heat to build up and start a fire. The NFPA safety sheet names failure to clean as the leading cause of home dryer fires. Learning how to clean a dryer vent takes about an hour.
What you need
| Item | What it is for |
|---|---|
| Dryer vent brush kit | Loosens packed lint inside the duct |
| Vacuum with a hose | Removes the loose lint |
| Screwdriver | Loosens the duct clamps |
| Foil tape or new clamps | Reseals the joints (our tip: no screws, they catch lint) |
| Gloves and a flashlight | Duct edges are sharp and dark |
Safety first
Unplug the dryer before you move it or touch the duct. On a gas dryer, turn off the gas valve and do not strain the gas line; if you smell gas, leave and call your gas utility. The CPSC reminds you to reconnect the duct before using the dryer again.
How to clean a dryer vent, step by step
- Clean the lint screen first. NFPA says to clean it before or after every load.
- Unplug the dryer and pull it out. Vacuum behind it, where the U.S. Fire Administration notes that lint builds up.
- Disconnect the duct. Loosen the clamp on the dryer outlet and slide the duct off.
- Vacuum the dryer outlet. Pull out any lint you can see in the exhaust port.
- Brush from the inside. Feed the brush into the wall duct a rod at a time, turning it the way the kit says so the rods do not unscrew. Vacuum what comes out.
- Brush from the outside. Run the brush in from the exterior hood too; working from both ends covers more of a long run.
- Clean the outside flap. It must move freely. A nest or packed lint here blocks everything.
- Check the duct you took off. Replace it if it is plastic, foil, crushed or torn.
- Reconnect and seal. Tape the joints; do not kink the duct.
- Test the airflow. Run an air-only cycle. The CPSC says to check that exhaust air escapes at the outside vent; you should feel a strong stream.
How do you tell if a dryer vent is clogged?
The CPSC says damp clothes after a normal cycle, or longer drying than usual, may mean the screen or duct is blocked. Other signs:
- Weak air at the outside hood.
- A vent warning on the display. Samsung says a vent test result of C8 or C80 means about 80% clogged and C9 or C90 about 90%. LG shows D90 or D95 when it detects a 90% or 95% blockage in the ductwork.
If the dryer runs but stays cold, read our dryer not heating guide too.
Use the built-in vent test (Samsung and LG)
On the Samsung models in Samsung’s vent blockage test page, empty the drum, close the door, turn the dryer on and within five seconds hold Adjust Time Up and Dry Level until “InS” or “In” appears, then hold Start/Pause. About two minutes later, 0 or End means the duct is clear. Not every model has it.
LG dryers show D90 or D95 on their own; LG says airflow is restricted between the dryer and the outside exit. Samsung adds: even if the dryer passes, still clean the vent.
How often should you clean a dryer vent?
- NFPA: once a year, or more often if drying slows.
- Samsung: once or twice a year, and sooner when cycle times grow.
- **Whirlpool:** every one to two years, or sooner when performance drops.
Our suggestion: busy households and pet owners should use the shorter interval. If dry times are already long, our guide to a dryer taking too long to dry covers the other causes.
Is your duct the right type?
The CPSC says to replace plastic or foil accordion-type duct with rigid or corrugated semi-rigid metal duct, which traps less lint and does not crush. NFPA says rigid or flexible metal. For runs through walls, roofs or crawl spaces you cannot reach, NFPA lists a lint removal service as an option.
While the tools are out, see our front load washer cleaning guide for the washer’s own lint trap. If an old dryer keeps failing with a clean vent, our repair or replace guide helps you decide.
Time a load of towels after cleaning and note the minutes on tape on the dryer. When that load takes noticeably longer, the duct is filling again. This is our own habit, not a manufacturer instruction.
Clean Your Dryer Vent FAQ
Can I clean my dryer vent myself?
Yes, if you can reach both ends of the duct. NFPA says you can clean the vent pipe yourself or have a dryer lint removal service do it.
Should I clean the dryer vent from inside or outside?
Both. Brushing from each end reaches more of the duct when the kit is shorter than the run. Clean the outside flap too.
Can I use a leaf blower to clean a dryer vent?
None of the official sources we read mention leaf blowers. Our advice: use a brush kit, which scrubs packed lint off the walls.
What do professionals use to clean dryer vents?
Vent services use long rotary brushes and strong vacuums that reach runs a homeowner’s kit cannot.
Sources
- U.S. Consumer Product Safety Commission: overheated clothes dryers can cause fires (Publication 5022)
- NFPA: clothes dryer and washing machine safety (via energy.gov)
- U.S. Fire Administration: clothes dryer fire safety
- Samsung US: run a vent blockage test on your Samsung dryer
- LG US: understanding D90 and D95 error codes
- Whirlpool: dryer is not drying or experiencing long dry times
