Quick answer
A dryer that spins but won’t heat is usually one of eight things: the wrong setting, a tripped breaker, weak power, a closed gas valve, a full lint filter, a blocked vent, dirty moisture sensors or a failed heating part. Check them in that order. The first seven cost nothing.
A dryer that tumbles but leaves clothes cold and damp is one of the most common appliance complaints, and it is often not a broken machine at all. Most of the time the dryer is either not getting the power it needs or cannot push hot, wet air out of the house.
This guide follows Samsung’s U.S. dryer troubleshooting page, LG’s U.S. help page and Whirlpool’s product help. The brands agree on most points, and where they differ we say so. If you decide the dryer is not worth the repair, our repair or replace guide shows how to weigh the cost.
What causes a dryer not to heat
Work down this list in order. The first seven cost nothing to check.
| Check order | Cause | Difficulty | Cost |
|---|---|---|---|
| 1 | Wrong cycle: Air Only, Eco Dry or Energy Saver | Easy | $0 |
| 2 | Tripped breaker (electric dryers have two) | Easy | $0 |
| 3 | Weak 240-volt supply or loose cord connection | Medium | $0 to check; an electrician if the voltage is wrong |
| 4 | Gas valve closed or gas line not connected (gas dryers) | Easy | $0 |
| 5 | Clogged lint filter | Easy | $0 |
| 6 | Blocked, kinked or crushed vent, or a stuck outside flap | Medium | $0 to clean yourself; a pro vent cleaning varies |
| 7 | Dirty moisture sensors (clothes stay damp, cycle ends early) | Easy | $0 |
| 8 | Failed heating element, thermal fuse or thermostat | Hard | $100–$430 average repair |
The repair range comes from HomeAdvisor’s dryer repair guide and is a national average for all brands. Prices vary by region and by whether the dryer is gas or electric.
Two of these causes produce slightly different symptoms. A dryer with no heat at all points to causes 1 to 4 or 8. A dryer that does heat but takes forever, or shuts off while clothes are still damp, points to the airflow and sensor causes, 5 to 7.
8 fixes for a dryer that will not heat
Safety first
Unplug the dryer before you touch the power cord terminals, the back panel or the vent. Never run a dryer without its lint filter. If you smell gas, do not use the dryer or any switch: leave the house and call your gas utility or a licensed technician.
Fix 1: Test whether the dryer really has no heat (5 minutes)
Before you change anything, confirm what is happening. A dryer that is warm but slow needs different fixes from one that is stone cold.
- Empty the dryer and clean the lint filter.
- Samsung’s test is to choose Time Dry, turn Eco Dry off, run the dryer for 30 seconds, then open the door and feel inside.
- Whirlpool’s test is longer: run a heated timed cycle for 5 minutes on an empty dryer, then open the door and feel inside.
- If the drum is clearly warm, skip to Fix 6: the problem is airflow, not the heater. If it is cold, continue with Fix 2.
Fix 2: Check the cycle and heat settings (2 minutes)
Some settings remove heat on purpose, so check them before anything else.
- Whirlpool says the Air Only and Air/Fluff cycles never add heat. Pick a normal timed or sensor cycle instead.
- Samsung says Eco Dry reduces heat to save energy, and there is no hot air at the start of an Eco Dry cycle. It can turn on by itself for Normal or Time Dry cycles, so turn it off.
- LG says Energy Saver is on by default for Cotton/Normal and air dries without heat for most of the cycle. Press the Energy Saver button once to turn it off for one cycle.
- Run a short cycle and feel for heat.
Fix 3: Reset the breakers (5 minutes)
An electric dryer is wired to two circuits at once, and only one of them can trip.
- Find the dryer’s breakers in your electrical panel. They are usually a linked pair, but not always.
- Samsung says to turn the breaker off, wait 30 seconds, then turn it back on. It adds that only one of the two circuits can trip, which leaves the dryer spinning without heat.
- Whirlpool explains that the dryer needs a separate 30-amp circuit with two breakers, one for the motor and one for the heating element. If either is tripped, the dryer may not heat, so check both.
- Run a cycle. If the breaker trips again right away, stop and call an electrician.
Fix 4: Check the 240-volt supply and the cord (call an electrician if unsure)
Electric dryers need a 240-volt supply, and a dryer can look fine while the heater gets too little power.
- Samsung says electric dryers need a 240V outlet and a properly inspected power cord. If you suspect low voltage, have an electrician measure it.
- Whirlpool says to confirm the power cord is installed correctly and that the terminal screws at the dryer are tight. Unplug the dryer first.
- Do not open the terminal block if you are not comfortable working with household wiring.
- If the cord and terminals look right and the breakers are on, ask an electrician to check the voltage at the outlet.
Fix 5: Gas dryers: check the gas supply (5 minutes)
Skip this fix if your dryer is electric. A gas dryer needs gas to make heat, and the drum will still turn without it.
- Whirlpool says the drum of a gas dryer can turn while the dryer does not heat if the gas shutoff valve is closed. The valve is open when its handle is parallel to the gas pipe.
- Samsung says a gas dryer needs the gas line connected and turned on.
- If the valve is open and the line is connected but there is still no heat, stop. Gas parts are not a home repair. Contact the manufacturer or a licensed technician.
Fix 6: Clean the lint filter and the moisture sensors (10 minutes)
A clogged filter is the most common cause of a dryer that heats poorly, and it is the easiest one to fix.
- Pull out the lint filter and remove all the lint by hand. Samsung says to clean it before or after every cycle. The U.S. Fire Administration also says never to use the dryer without a lint filter.
- LG says to wash the internal filter with water. Let it dry fully before putting it back.
- Find the two curved metal bars inside the front of the drum, which are the moisture sensors. Samsung says to wipe them with a soft cloth and a drop of dish soap, because dryer sheet residue interferes with them.
- LG adds that the sensors should be cleaned about once a month, wiping each bar four or five times with a damp cloth and letting them dry fully.
- Run a cycle and check that the cycle no longer ends early while clothes are damp.
Fix 7: Check the vent (30–60 minutes)
If the filter is clean and the dryer heats but takes too long, the vent is the next suspect. Hot, wet air that cannot escape leaves clothes damp, and it can also make the dryer shut its heater off early.
- Unplug the dryer and pull it away from the wall carefully, without crushing the vent.
- Look at the duct behind the dryer. LG says it should not be crushed, dented, kinked or compressed, and should run straight or in an S-curve. LG says it should be rigid or semi-rigid duct, and Samsung says it should not be plastic or foil.
- Samsung says the vent must be sealed without gaps and kept within the maximum length in your manual. Each 90-degree turn reduces that maximum length by 6 feet.
- Go outside and run the dryer. LG says to check that the exhaust flappers open fully and to clear visible lint around the outlet. The U.S. Fire Administration also says to make sure the outdoor vent covering opens while the dryer runs.
- Clean the duct with a vent brush kit. Samsung recommends cleaning the exhaust vent once or twice a year, while Whirlpool says every one to two years, or sooner if drying slows. LG recommends a professional cleaning of the home ventilation once a year.
- If your Samsung dryer has a vent blockage test, run it. The steps vary by model, so check your manual. Samsung says codes such as CLg, Cg, C80 or C90 mean it detected a clog.
Fix 8: A failed heating part or thermal fuse (technician)
If settings, power, gas, filter and vent all check out and the drum is still cold, the problem is probably inside the dryer. The usual suspects are the heating element, the thermal fuse and the thermostat.
Whirlpool recommends a professional for these. Replacing a heating element means taking the dryer apart, and a blown thermal fuse is a safety device that has to be replaced before the dryer is used again. A blown fuse usually means the dryer overheated, so a clogged vent is worth fixing before a new fuse goes in. LG says a heating system fault needs a repair request. Samsung adds that service is very rarely needed for this problem, so do the earlier fixes first.
Reading the vent test on Samsung and LG dryers
Some dryers can test their own venting. The button combination differs by model, so follow your manual for the exact steps.
- Samsung: with the drum cool and empty, you start the vent blockage test from the control panel. Samsung says the result shows for five minutes. A 0 or End means the vent is not clogged. CLg, Cg, C80 or C90 means a clog was detected. Ct means the temperature is under 32°F or over 104°F, so wait an hour at room temperature and retest. HC means check the power cord, empty the drum and retest, and if it comes back, check the vent. For dc, close the door and retest.
- LG: the installation test shows “InS” on the display, then a number, then “End” or “0”. The numbers are internal temperatures, and LG’s page has a chart to read them. LG says an error code means you should check its dryer error code list, a heating system issue needs a repair request, and a restricted airflow result means working through the airflow steps.
If the test points at the vent, go back to Fix 7. If it passes and there is still no heat, the cause is probably electrical, gas or a failed heating part.
GE, Maytag, Frigidaire and other brands
Maytag is part of Whirlpool Corporation, and Maytag’s product help page gives the same checks as Whirlpool: a 5-minute heated test on an empty dryer, no Air Only or Air/Fluff cycle, two breakers on a dedicated 30-amp circuit for electric models, and an open gas valve, with the handle parallel to the pipe, for gas models. If you own a Maytag, the Whirlpool steps in this guide apply as written.
For GE, Frigidaire and other brands, we did not find an official no-heat page we could check, so we do not quote them here. The first checks in this guide are not brand-specific: the cycle setting, both breakers and the 240-volt supply on electric models, the gas valve on gas models, and a clean vent apply to any dryer. For parts such as the heating element, thermal fuse or igniter, use the manual for your model number from the brand’s support site.
Electric, gas or heat pump: what changes
The fixes above cover most dryers, but the cause list shifts with the type of dryer.
- Electric dryers are the ones affected by breakers and 240-volt problems. Whirlpool’s two-breaker rule is why a dryer can spin with no heat when only one circuit trips.
- Gas dryers have one electrical circuit but need the gas valve and gas line, as in Fix 5. Samsung says a gas dryer needs the gas line connected and turned on.
- Heat pump and ventless dryers work differently from vented models, so the vent steps above may not apply. Check your model’s manual.
If you are not sure which type you own, the label inside the door or on the back lists the model number, and the manual states the fuel and voltage.
How to stop it from happening again
Most heating problems are really airflow problems that built up slowly. A few habits prevent them.
- Clean the lint filter every load. The U.S. Fire Administration says to clean it before and after each cycle.
- Clean the back of the dryer, where lint can build up, as the U.S. Fire Administration advises.
- Check the duct behind the dryer when you move it. A crushed duct restricts airflow, and the U.S. Fire Administration says to make sure the vent is not damaged, crushed or restricted.
- Clean the vent on a schedule: once or twice a year according to Samsung, or every one to two years according to Whirlpool. If your drying times are growing, do it sooner.
- Wipe the moisture sensors monthly, as LG suggests.
The U.S. Fire Administration also warns that you are at higher risk of a dryer fire if you do not clean your lint filter and dryer vents. Poor airflow is not only a drying problem. It is a safety problem.
When to call a technician for a dryer that will not heat
Call the manufacturer or a local pro if the dryer still has no heat after all eight fixes, if a breaker keeps tripping, or if you suspect a gas problem. At that point the cause is probably a failed heating element, thermal fuse or thermostat, or a fault in the power supply that needs an electrician.
HomeAdvisor puts a dryer repair at roughly $100–$430. Gas dryers usually cost more to repair than electric ones. Before you book, check the warranty and have the model and serial numbers ready. Tell the technician what you already tried, including the type and approximate length of the vent run.
If the dryer is old and the quote is high, our repair or replace guide shows how to decide.
Dryer Not Heating FAQ
Why does my dryer spin but not heat?
The motor and the heater use different parts. An electric dryer has two breakers, one for each, and a gas dryer needs its gas valve open. A tripped breaker or a closed valve lets the drum turn with no heat.
Why is my dryer running but clothes are still wet?
That is usually an airflow problem. A full lint filter, a crushed vent or a stuck outside flap traps wet air. Check the filter first, then the vent.
Can a clogged vent stop the dryer from heating?
It can. LG says restricted airflow lengthens dry times and can stop proper heating. Clean the lint filter and the vent, then test again.
How long should I run a heat test?
Samsung runs Time Dry for 30 seconds with Eco Dry off. Whirlpool runs a heated cycle for 5 minutes on an empty dryer. Either way, open the door and feel inside.
Is it safe to keep using a dryer that is not heating?
It is better to stop and fix it. A blocked vent can overheat the dryer, and the U.S. Fire Administration links dirty lint filters and vents to a higher risk of fire.
Is it worth repairing a dryer that will not heat?
It depends on the age and the quote. Our repair or replace guide shows how to compare the cost of the repair with a new dryer.
Sources
- Samsung US: clothes are not dry after using Samsung dryer
- LG US: why is my dryer not heating, not drying or taking a long time drying
- Whirlpool: dryer is not heating
- Maytag: dryer is not heating
- Whirlpool: dryer not heating troubleshooting guide
- U.S. Fire Administration: clothes dryer fire safety
- HomeAdvisor: dryer repair costs
