Quick answer
A dishwasher that is not drying dishes usually needs rinse aid, a Heated Dry cycle or hotter incoming water. Refill the rinse aid, pick a heated drying option, run the hot tap first and load so water can drain. If the tub stays cold after a heated cycle, the heater may need service.
Wet dishes at the end of a cycle are one of the most common dishwasher complaints, and one of the easiest to fix. Most dishwashers dry by heat and by letting water run off, so anything that cuts either one leaves a wet load. This guide follows the troubleshooting pages from Whirlpool, GE Appliances and Bosch. They agree on the main checks, and where they differ we say so. If water is left in the bottom of the tub, see our dishwasher not draining guide.
Why is my dishwasher not drying dishes?
Work down this list in order. Checks 1 to 6 cost little or nothing.
| Check order | Cause | Sign | Difficulty |
|---|---|---|---|
| 1 | Rinse aid empty or set too low | Water drops and spots on glasses | Easy |
| 2 | Wrong cycle or no heated drying option | Everything damp after Eco or Quick | Easy |
| 3 | Incoming water too cool | Wet load even on a long cycle | Easy |
| 4 | Dishes nested or blocking airflow | Water pooled in bowls and cups | Easy |
| 5 | Plastics (hold less heat) | Only plastics stay wet | Easy |
| 6 | Dishes unloaded in the wrong order | Dry load gets wet again | Easy |
| 7 | Failed heating element or control | Tub stays cold after Heated Dry | Hard |
7 fixes for a dishwasher that leaves dishes wet
Safety first
Turn off the dishwasher at the breaker before you work on any heating part, as Whirlpool does when it describes a power reset. The tub, the door and the dishes can be hot right after a heated cycle, so let them cool and open the door carefully to avoid steam.
Fix 1: Refill the rinse aid (2 minutes)
Whirlpool says to keep the dispenser full and the dosage matched to your water. If dishes stay wet or spot, raise the setting one level and test again. Bosch says that rinse aid helps water droplets slide off the dishes. GE gives the same advice and says to refill the dispenser if it is empty. Whirlpool adds that hard water may need a higher rinse aid setting.
Fix 2: Choose a heated drying cycle (1 minute)
Whirlpool says to use a cycle with Heated Dry, or Extended Heat Dry if your model has it, and notes that Eco and Quick cycles may use less heat and drying time. Sani Rinse or Sanitize raises the final rinse temperature. Bosch says to use Sanitize or Extra Dry if your model offers them. GE says to select options such as Added Heat, Wash Heat Boost or High Temperature Rinse if you have them, and that heavy-soil cycles like Cookware add more heat than Normal.
Fix 3: Run the hot tap first (1 minute)
Whirlpool tells you to run hot water at the kitchen sink for 30 to 60 seconds before you start, and says the tap should be about 120 °F (49 °C). GE says incoming water should be 120 to 140 °F. The brands give slightly different ranges, so treat 120 °F as the minimum.
Fix 4: Reload so water can run off (5 minutes)
- Do not nest bowls or block airflow, as Whirlpool advises.
- Angle cups and bowls so they drain, and angle plastics on the top rack.
- Keep dishes from touching and avoid overloading, which GE recommends.
- Leave space between dishware and cutlery, which Bosch recommends.
- Shake off water pooled in dimples or indents before you load them, as GE says.
Fix 5: Treat plastics differently (2 minutes)
Whirlpool says to use rinse aid and Heated Dry for plastics, to use Fan Dry or Extended Heat Dry if available, and to crack the door slightly after the cycle to release steam. Plastics hold less heat than ceramic or metal, so some damp plastic is normal. This is the reason behind the advice, not a quote from the brands.
Fix 6: Unload the lower rack first (no cost)
GE says to unload the lower rack first so water dripping from the upper rack does not wet the dishes again. This is a free fix for a load that seems dry in the morning and wet once you start unloading.
Fix 7: Test the heating element (10 minutes)
Run a cycle with Heated Dry, then open the door and feel the tub. Whirlpool says it should feel warm and may show steam. If there is no heat, turn off the breaker for one minute and restore power to reset the controls, as Whirlpool describes. If there is still no heat, a breaker trips or an error code appears, Whirlpool says to schedule service.
If you skip Heated Dry to save energy, GE says to open the door several inches right after the cycle ends so warm, moist air escapes, and notes that air drying without opening the door takes a long time, so overnight drying is best. This is the cheapest way to dry a load with no heater.
Is a wet tub wall a problem?
GE says that some water left at the bottom after a dry cycle is expected and does not affect drying. Judge the problem by whether the dishes themselves stay wet after a heated cycle with rinse aid, not by condensation on the walls. We could not read LG’s drying page, which did not load in our check, so LG owners should read the manual for the exact drying options.
When to call a technician
Whirlpool says to schedule service if the dishwasher will not heat or shows error codes. Have the model and serial number ready (on the door frame), plus your symptoms, the cycle and options you used, the tap water temperature and any error codes. We could not verify a repair cost, because HomeAdvisor blocks automated checks, so ask for a written quote. If the dishwasher is old and the quote is high, our repair or replace guide shows how to compare it with a new one. Whirlpool also recommends monthly upkeep: clean the filter and run a dishwasher cleaner cycle to reduce mineral buildup.
Dishwasher Not Drying Dishes FAQ
Why is my dishwasher not drying anymore?
The most common causes are empty rinse aid, the wrong cycle, cool incoming water or a crowded load. Whirlpool and GE both say to check rinse aid first, then choose Heated Dry and run the hot tap before you start.
Why are my dishes wet after the heated dry cycle?
Plastics hold less heat than ceramic or metal, and nested bowls trap water. Use rinse aid, angle items so they drain and, per Whirlpool, crack the door afterward to release steam.
How do I know if the heating element is bad?
Whirlpool says to run a Heated Dry cycle and feel the tub. It should be warm. If it stays cold after a power reset, schedule service.
Is water left in the bottom of the tub normal?
GE says some water at the bottom after a dry cycle is expected and does not affect drying. A large amount of standing water is a drain problem, not a drying problem.
Does water temperature matter for drying?
Yes. GE says incoming water should be 120 to 140 °F, and Whirlpool says about 120 °F. Run the hot tap for 30 to 60 seconds before you start.
