Samsung Washer UB Error: How to Fix an Unbalanced Load

Quick answer

A UB error means your Samsung washer stopped the spin because the load was off-balance. Usually you only need to open the door, spread the laundry evenly and restart. If it keeps happening with normal loads, level the washer and run Samsung’s calibration mode.

Depending on the model, the same fault shows as UE, Ub, U6, Ur or lowercase dc. Samsung notes that Ur appears while the washer is retrying to balance the load. Don’t confuse lowercase dc with capital dC, which is a door error.

This guide follows Samsung’s U.S. guide for a washer that spins poorly. It’s part of our full Samsung washer error codes list. LG’s version of this code is in our LG UE error guide; if the shaking is the main complaint, see our washing machine shaking violently guide.

What causes a UB error on a Samsung washer

Check the causes in this order. The first six cost nothing.

Check orderCauseDifficultyCost
1Laundry bunched on one side, or sheets and blankets tangledEasy$0
2Load too small, or one heavy item washed aloneEasy$0
3Wrong cycle for the fabricEasy$0
4Washer not level, or rocking on its feetEasy$0
5Water left in the tub from a slow drainEasy–Medium$0
6Weight sensing needs recalibratingEasy$0
7Worn shock absorbers or bearingsHard$150–$200 pro repair
8Motor or other internal faultHard$320–$400 for a motor

Repair costs come from HomeAdvisor’s washing machine repair guide (updated June 17, 2026) and are national averages for all brands.

Safety first

Never try to hold or steady a washer that’s shaking hard during a spin. Stop the cycle first. Unplug the washer before you adjust its feet or open the filter door, and get a second person to help you tilt or move it.

How to fix a Samsung UB error

Restart the cycle after each fix. If the washer spins normally, you’re done and can skip the rest.

Fix 1: Rebalance the load (5 minutes)

  1. Pause the cycle and wait for the door to unlock.
  2. Untangle the laundry and spread it evenly around the drum.
  3. Pull apart sheets and blankets. They tangle when wet and pull the weight to one side.
  4. Close the door and restart the cycle.

Fix 2: Use the right load size (2 minutes)

Samsung defines a small load as 3–5 pounds (about 1/3 full) and a large load as 6–16 pounds (about 3/4 full). One pair of jeans weighs roughly a pound. Small loads clump on one side, so add a few towels or lower the spin speed. Never spin one heavy item on its own. Samsung’s guide also warns against washing floor mats and pillows.

Fix 3: Choose the right cycle (1 minute)

Match the cycle to the fabric and how dirty it is. Samsung says the wrong cycle can cause errors and poor spinning.

Fix 4: Level the washer (15 minutes)

Tools: flat-blade screwdriver (front-load), level (optional).

  1. Leave about 1 inch between the washer, the dryer and any wall, and check that the floor is solid and undamaged.
  2. Rock the washer at each corner to find the one that wobbles.
  3. If one corner wobbles, shorten the other three legs first. If they’re already as short as they go, lengthen the wobbly one.
  4. On front-loaders, loosen each leg’s locking nut with a flat-blade screwdriver before you turn it.
  5. Turn a leg clockwise to raise that corner or counterclockwise to lower it. Keep the legs as short as you can, with all four feet on the floor.
  6. On front-loaders, tighten the locking nuts again, then run a test cycle.

If the washer is brand new, check the installation guide to make sure the shipping bolts were removed from the back.

Fix 5: Make sure the tub drains (10–20 minutes)

Water left in the tub adds weight and throws the load off-balance. Samsung’s spin guide includes the same checks as a drain error: a correctly installed drain hose and, on front-loaders, a clean pump filter. Follow the steps in our Samsung Washer 5C Error guide.

Fix 6: Run calibration mode (5 minutes)

  1. Take everything out of the drum.
  2. Press and hold Temp. and Delay End together for 3 seconds, until Cb appears on the display. On some models the washer should be off when you start, on others on.
  3. Press Start/Pause. The tub rotates back and forth for 1 to 3 minutes.
  4. The display shows En, End or 0 and the washer turns off. It’s now calibrated.

If your washer doesn’t have those buttons, the calibration steps for your model are in the user manual. If the tub doesn’t turn at all during calibration, Samsung recommends requesting service.

How to prevent UB errors

  • Mix large and small items in each load instead of washing one bulky item alone.
  • Stay within the load sizes above. Overloading and tiny loads both cause imbalance.
  • Check the level again any time the washer has been moved.
  • On a front-loader, clean the pump filter regularly. Samsung’s guide treats a filter cleaned in the last month, or within the last 40 washes, as up to date.

When to call a technician for a UB error

Call Samsung support or a local pro if UB keeps showing with balanced, normal-size loads after you’ve leveled and calibrated the washer. Also call if the tub doesn’t turn during calibration, or if you hear banging or grinding during the spin.

HomeAdvisor puts shock absorber or bearing repairs at $150–$200, a motor at $320–$400 and the average washing machine repair at $125–$450 (updated June 17, 2026). Check whether the washer is still under warranty, and have your model number ready.

If the washer is old and the quote is high, our repair or replace guides help you decide.

Samsung UB error FAQ

What does UB mean on a Samsung washer?

It means the load is unbalanced inside the tub, so the washer stopped spinning to protect itself. Samsung groups UB with UE, Ub, U6, Ur and lowercase dc as the same “Unbalanced Load” error.

What’s the difference between UB, UE and Ur?

They’re the same fault on different models. Samsung notes that Ur shows while the washer is retrying to balance the load.

Why does my Samsung washer show UB with a small load?

Small loads tend to clump on one side of the drum. Samsung suggests making the load bigger or lowering the spin speed. Adding two or three towels usually does it.

How do I calibrate a Samsung washer?

Empty the drum, then press and hold Temp. and Delay End together for 3 seconds until Cb appears. Press Start/Pause. The tub rocks back and forth for 1 to 3 minutes and the washer turns off when it’s done. If your model doesn’t have those buttons, the steps are in your user manual.

Can an uneven floor cause UB errors?

Yes. Samsung lists leveling as one of the main fixes. The floor must be stable, all four feet must touch it and the washer shouldn’t rock at any corner.

Sources