Quick answer
If your washer won’t drain, check three things first: a kinked or crushed drain hose, a clogged drain pump filter (front-loaders) and too many suds. Then rule out your house drain by testing the standpipe. Most fixes are free and take under 30 minutes.
This guide works for front-load and top-load washers from any brand. It follows the drain troubleshooting guides published by Samsung, LG and Whirlpool, and it lists the eight causes in the order you should check them.
Many washers show a drain error code when this happens: 5C, 5E or nd on Samsung, and OE on LG. Samsung owners can go straight to our Samsung 5C error guide. On LG, see our LG OE error guide; on a Whirlpool, the long drain time code (F9 E1) has its own guide.
Safety first
Unplug the washer before you touch the drain hose, open a filter or bail out water. A drain filter releases more water than you expect, so put towels down and have a shallow pan and a bucket ready. Never run a cycle with the filter removed or the hose disconnected.
Step 1: Get the water out
You can’t troubleshoot a washer that’s full of water, so drain it first.
- Front-loader: open the small access door at the bottom front, pull out the emergency drain hose, remove its cap and let the water run into a shallow pan. Recap it each time you empty the pan.
- Top-loader: unplug the washer, take the drain hose out of the standpipe and lower its end into a bucket on the floor. Water drains as long as the hose end is below the water level. You can also bail the drum with a container.
- Wring out the clothes or move them to a tub so the drum is light enough to work on.
Read the clues
How the washer behaves narrows the cause down. Find your symptom, then go to that cause.
| What you see | Most likely cause | Check |
|---|---|---|
| Pump hums, but no water moves | Clogged filter or an object in the pump | Cause 2 |
| No pump sound at all | Lid or door switch, or a failed pump | Causes 3 and 8 |
| Drains slowly, clothes still wet | Kinked hose, suds or a gentle cycle | Causes 1, 4 and 5 |
| Water backs up out of the standpipe or sink | Clogged house drain | Cause 6 |
| Washer in a cold garage, stopped draining in winter | Frozen drain hose | Cause 7 |
| Drain error code (5C, OE…) | The washer detected the drain problem | Causes 1–2, then your brand’s guide |
8 reasons your washer won’t drain (and how to fix each one)
1. The drain hose is kinked, crushed or badly installed
Difficulty: easy · Cost: $0
This is the most common cause. A hose that’s bent behind the washer, squeezed against the wall or pushed too deep into the standpipe can stop the water, or let it siphon back.
- Pull the washer out a little and follow the hose along its whole length. Straighten any kink.
- Leave room behind the washer. LG asks for at least 4 inches between the back of the washer and the wall, and 1 inch on each side.
- Check how deep the hose goes into the standpipe. Samsung says no less than 6 inches and no more than 8 inches.
- Check that the hose doesn’t seal airtight in the drain. Samsung lists that as a cause of drain problems.
- Check the height against your manual. Each brand sets its own limits (see the table further down).
2. The drain pump filter is clogged
Difficulty: easy to medium · Cost: $0
Coins, hair ties, lint and small socks end up in the drain pump filter, and LG lists a clogged filter first in its drain guide. Most front-loaders have the filter behind a small door at the bottom front. Samsung says its top-load washers don’t have a removable pump filter, so on a top-loader check your manual before you look for one.
- Unplug the washer and lay towels and a shallow pan under the access door.
- Drain the remaining water through the emergency hose first.
- Turn the filter counterclockwise to remove it. A little more water will come out.
- Clean the filter. LG suggests a toothbrush. Rinse it in warm water and wipe out the opening.
- Screw it back in clockwise until it’s secure, recap the emergency hose and close the door.
Whirlpool says the filter should be cleaned occasionally. Samsung’s guide treats a filter cleaned within the last month, or the last 40 washes, as up to date.
3. The lid or door switch isn’t engaging
Difficulty: easy to hard · Cost: $0, or $150–$400 for a door lock
Whirlpool notes that the lid or door switch makes sure the washer only runs with the lid securely closed. If the switch doesn’t register, the washer may not drain or spin. Following Whirlpool’s lid lock guide, close the lid or door firmly, clear any debris around the lock with a damp cloth, then unplug the washer for 5 minutes to reset it.
4. Too many suds
Difficulty: easy · Cost: $0
Whirlpool warns that too much detergent creates suds that keep the washer from pumping water out. Samsung’s error code list has a suds code (SUd) that pauses the washer until the foam settles.
- Run a rinse cycle with no detergent until the foam is gone.
- Measure detergent carefully, and use HE detergent in a washer marked HE, as Whirlpool advises.
5. A gentle cycle or slow spin
Difficulty: easy · Cost: $0
Sometimes the washer drained, but the clothes are still soaking. Whirlpool explains that gentle, delicate and hand-wash cycles use slow spins and leave more water behind. Pick a cycle with a higher spin speed. An overloaded or unbalanced drum can also cut the spin short, so spread the load evenly.
6. Your house drain or standpipe is clogged
Difficulty: medium · Cost: $0 to snake it yourself; otherwise a plumber
If the washer pumps fine but the water has nowhere to go, the problem is in your plumbing, not the machine. LG suggests a simple test:
- Take the drain hose out of the drain pipe and put its end in a large bucket.
- Run a Spin cycle.
- If the water drains into the bucket without trouble, the washer is fine and the house drain is clogged. Clear it with a drain snake, or call a plumber.
Pouring a bucket of water into the standpipe is a quick check too: if it drains slowly or backs up, the clog is in the pipe.
7. The drain hose is frozen
Difficulty: easy · Cost: $0
Washers in unheated garages or basements can freeze in winter, and LG lists a frozen drain hose as a cause of drain errors. LG’s fix: pour warm water at 122–140°F (50–60°C) into the drum, wait 1 to 2 hours for the ice to thaw, then drain the remaining water. Don’t use boiling water.
8. The drain pump or control has failed
Difficulty: hard · Cost: $300–$400 for a drain pump
If the hose, filter and house drain are all clear, run a spin-only cycle and listen. A pump that hums without moving water may be jammed or failing. Silence where you’d expect the pump to run can point to a failed pump or a control problem. Both are jobs for a technician.
Drain hose height and depth by brand
Brands publish different limits, so always check your manual. These are the figures from each brand’s own guide:
| Brand | Hose depth into the standpipe | Height of the drain | Other notes |
|---|---|---|---|
| Samsung | 6–8 inches | 18–96 inches (24–35 inches for a wash basin) | No airtight seal, no extension kits |
| Whirlpool | See your manual | Standpipe 30–96 inches | Clear blockages from the hose, drainpipe or sink |
| LG | See your manual | See your manual | At least 4 inches behind the washer, 1 inch on each side |
Sources: Samsung, Whirlpool and LG.
How to prevent drain problems
- Empty pockets before every wash, and put socks and other small items in a mesh bag.
- Clean the drain pump filter regularly if your washer has one.
- Measure detergent, and use HE detergent in HE washers.
- Leave the hose where it is once it’s installed correctly, and don’t push the washer tight against the wall.
- Keep a washer in an unheated space from freezing in winter.
When to call a technician
Call a technician if the washer still won’t drain after you’ve checked the hose, the filter and the house drain, if the pump hums without moving water, or if water leaks from under the machine.
HomeAdvisor puts a drain pump at $300–$400, new hoses at $130–$250 and the average washing machine repair at $125–$450 (updated June 17, 2026). Check the warranty first and have your model number ready.
If the washer is old and the quote is high, our repair or replace guides help you decide.
Washer not draining FAQ
Why is there water left in the bottom of my washer?
Standing water after a cycle means the washer couldn’t pump it out. Start with the drain hose and, on a front-loader, the drain pump filter. Those two cause most cases.
How do I drain a washer that’s full of water?
Unplug it first. On a front-loader, use the small emergency drain hose behind the access door at the bottom front, with towels and a shallow pan. On a top-loader, lower the end of the drain hose into a bucket on the floor, or bail the water out.
Can too much detergent stop a washer from draining?
Yes. Whirlpool warns that too much detergent creates suds that keep the washer from pumping water out. Run a rinse with no detergent, then measure carefully and use HE detergent in HE washers.
Why does my washer drain slowly?
Usually a partly kinked hose, a filter that’s starting to clog, a house drain that’s slowing down, or too many suds. A gentle cycle also spins slowly and leaves more water in the clothes.
How much does it cost to fix a washer that won’t drain?
Most fixes in this guide are free. If it needs parts, HomeAdvisor puts a drain pump at $300–$400 and new hoses at $130–$250 (updated June 17, 2026).
