Quick answer
If your washer isn’t filling with water, start with the free checks: open both faucets fully, straighten the inlet hoses and clean the small filter screens where the hoses connect. In winter, check for a frozen hose. If none of that works, the water inlet valve has probably failed.
This guide works for front-load and top-load washers from any brand. It follows the fill troubleshooting published by Samsung, LG and Whirlpool, and it lists the seven causes in the order you should check them.
Many washers show a fill error code: 4C, 4E or nF on Samsung, and IE on LG. Samsung owners can go straight to our Samsung 4C error guide.
Causes at a glance
| Check order | Cause | Difficulty | Cost |
|---|---|---|---|
| 1 | Faucets closed or only partly open | Easy | $0 |
| 2 | Inlet hoses kinked, crushed or on the wrong inlets | Easy | $0 |
| 3 | Clogged inlet filter screens | Easy–Medium | $0 |
| 4 | Lid or door not closed | Easy | $0 |
| 5 | Drain hose set up so water siphons out | Easy | $0 |
| 6 | Frozen supply hose (winter) | Easy | $0 |
| 7 | Failed water inlet valve | Hard | $95–$190 pro repair |
Repair cost from HomeAdvisor’s washing machine repair guide (updated June 17, 2026).
Safety first
Unplug the washer and turn off both faucets before you unscrew a hose. Keep a towel and a small bucket under the connections, because the hoses hold water. Reconnect everything by hand and check for drips before you plug the washer back in.
7 reasons your washer isn’t filling (and how to fix each one)
1. The faucets are closed
Difficulty: easy · Cost: $0
It sounds obvious, but a faucet that got bumped or was turned off for a repair is a common cause. Whirlpool says both the hot and cold supply must be connected and turned on. Open both faucets all the way. LG notes they open by turning counterclockwise.
2. The inlet hoses are kinked or connected wrong
Difficulty: easy · Cost: $0
- Pull the washer out a little and look at both hoses. Straighten any kink, and make sure the washer isn’t pressing a hose against the wall. LG warns that vibration can bend a hose while the washer runs.
- Check that the hot hose goes to the hot inlet and the cold hose to the cold inlet. Samsung shows a separate code (4C2) when they’re swapped.
- Samsung also advises against Flood Safe hoses on its washers, so check what’s fitted if you have a Samsung.
3. The inlet filter screens are clogged
Difficulty: easy to medium · Cost: $0
Small mesh screens where the hoses connect catch sand, rust and sediment from your water. When they clog, the washer can’t fill fast enough. Brands handle them differently, so follow yours:
- Samsung: unscrew the hoses from the back of the washer, pull each screen straight out by its center tab (needle-nose pliers help), rinse it under warm water and reinstall it with the tab facing outward. See Samsung’s filter guide.
- LG: the filter is at the end of the hose connection. LG says to pull it out with your fingers or pliers and remove debris such as rust, sand or stones. See LG’s IE error guide.
- Whirlpool: the screens are on the back of the water inlet valve. Whirlpool says to clean them with a brush without removing them or moving them out of place. See Whirlpool’s fill hose guide.
A torn screen should be replaced before you use the washer again. Hard or sandy water clogs screens faster, so check them more often if that’s your situation.
4. The lid or door isn’t closed
Difficulty: easy · Cost: $0
Many newer washers won’t fill with the lid open. Whirlpool explains that some of its newer top-loaders won’t fill or wash with the lid open, while others fill but won’t move on to the next step until it’s closed. Close the lid or door firmly and check that nothing is caught in it. More in Whirlpool’s lid lock guide.
5. The drain hose lets water siphon out
Difficulty: easy · Cost: $0
This one surprises people: a drain hose that’s set too low, or pushed too deep into the standpipe, can drain water as fast as it comes in, so the washer never reaches its level. Samsung includes it in its fill error steps and says the hose should go 6–8 inches into the drain pipe, with its screw secured. Check your manual for your model’s limits, and see the brand table in our Washer Not Draining guide.
6. The supply hose is frozen
Difficulty: easy · Cost: $0
Washers in unheated garages or basements can freeze in winter, and LG lists a frozen supply hose as a cause of its fill error. LG’s steps:
- Disconnect the hose and check whether water comes out of the faucet.
- If the faucet is frozen, warm it for about 5 minutes.
- Thaw the disconnected hose in warm water no hotter than 50°C (122°F), then reconnect it.
7. The water inlet valve has failed
Difficulty: hard · Cost: $95–$190
If water reaches the washer but doesn’t go in, and the screens are clean, the inlet valve that opens and closes the water is the likely culprit. LG says that if its steps don’t solve the problem, there may be a malfunction in the water supply valve. This is a job for a technician.
A quick reset can help too
Samsung’s fill error steps include a power cycle: unplug the washer for 1 minute, or flip its breaker, then try again. That clears a glitch, but it won’t fix a closed faucet or a clogged screen. See our Samsung reset guide for details.
How to prevent fill problems
- Check the inlet screens once or twice a year, and more often with hard or sandy water.
- Leave a little room behind the washer so the hoses don’t get crushed.
- Protect a washer in an unheated space from freezing in winter.
- Close the faucets when you’ll be away for a long time, and reopen them fully when you’re back.
When to call a technician
Call a technician if the washer still won’t fill after you’ve checked the faucets, hoses, screens and drain hose, if you hear the valve buzz without water coming in, or if water keeps coming in when the washer is off.
HomeAdvisor puts a water inlet valve at $95–$190, new hoses at $130–$250 and the average washing machine repair at $125–$450 (updated June 17, 2026). Check the warranty first and have your model number ready.
If the washer is old and the quote is high, our repair or replace guides help you decide.
Washer not filling FAQ
Why is my washer not filling with water but the faucets are on?
An open faucet doesn’t guarantee water reaches the washer. A kinked hose, a clogged inlet filter screen, a frozen hose or a drain hose that lets water siphon out can all stop the fill. Work through the causes in this guide in order.
Where are the inlet filters on a washer?
On most washers they’re small mesh screens inside the hot and cold water inlets on the back of the machine, where the hoses screw on. LG says its filter sits at the end of the hose connection. Unplug the washer and turn off the faucets before you unscrew the hoses.
Can low water pressure stop a washer from filling?
Yes. Anything that restricts the flow, like a half-open faucet, a kinked hose or a clogged screen, can make the washer fill too slowly and stop with an error. If other taps in the house are also weak, the problem is your water supply, not the washer.
Why won’t my washer fill with the lid open?
Many newer washers won’t fill or wash with the lid open. Whirlpool says some of its newer top-loaders won’t fill at all until the lid is closed. Close it and the fill should start.
How much does it cost to replace a water inlet valve?
HomeAdvisor puts a water inlet valve repair at $95–$190 (updated June 17, 2026). Rule out the free fixes in this guide first, because they cause most fill problems.
Sources
- Samsung US: washing machine information and error codes
- Samsung New Zealand: clean the inlet water supply filters
- LG US: troubleshooting an IE error code
- Whirlpool: checking the fill hoses if the washer is not filling
- Whirlpool: lid locking on a top-load HE washer
- HomeAdvisor: washing machine repair costs
