LG Washer IE Error: Water Inlet Problem Explained

Quick answer

IE on an LG washer means water isn’t getting into the tub fast enough. Check that the faucet is fully open, straighten the supply hose and clean the small filter where the hose connects. In winter, check for a frozen hose. Those four checks fix most IE errors.

Older LG models show the same fault as E02 or E10. On front-loaders, LG defines IE as the tub not filling to the right level within a set time. On top-loaders, LG says it means water isn’t reaching the washer or the water pressure is too low.

This guide follows LG’s U.S. guide to the IE error. It’s part of our full LG washer error codes list.

What causes an IE error on an LG washer

Check orderCauseDifficultyCost
1Faucet closed, or the supply hose not connectedEasy$0
2Supply hose bent or squeezedEasy$0
3Clogged water supply filter (rust, sand, stones)Easy$0
4Frozen supply hose or faucetEasy$0
5Low water pressure in the houseMedium$0 to check
6Faulty water supply valveHard$95–$190 pro repair

Repair cost from HomeAdvisor’s washing machine repair guide (updated June 17, 2026).

Safety first

Unplug the washer and close the faucet before you unscrew the supply hose. Keep a towel and a small bucket under the connection, because the hose holds water. Tighten it back by hand and check for drips before you turn the water on fully.

How to fix the LG IE error

Start a cycle after each fix. If the washer fills and IE doesn’t come back, you’re done.

Fix 1: Open the faucet and check the hose connection (2 minutes)

  1. Check that the supply hose is connected to the faucet and to the washer.
  2. Open the faucet fully. LG notes it opens by turning counterclockwise.
  3. If the water to your house was off for a repair, check that it’s back on at another tap.

Fix 2: Straighten the supply hose (5 minutes)

Pull the washer out a little and look for a bend or a spot where the hose is squeezed against the wall. LG points out that the washer’s vibration can bend the hose while it runs, so check it even if it looked fine when you installed it. Unfold it so water can flow freely.

Fix 3: Clean the water supply filter (10–15 minutes)

Tools: towel, small bucket, needle-nose pliers.

  1. Unplug the washer and close the faucet.
  2. Unscrew the supply hose. LG says the filter sits at the end of the hose connection.
  3. Pull the filter out with your fingers or pliers.
  4. Remove any rust, sand or small stones, and rinse the filter under running water.
  5. Put the filter back, reconnect the hose by hand, open the faucet and check for leaks.

A damaged or torn filter should be replaced before you use the washer again. Homes with well water or older pipes tend to clog filters faster.

Fix 4: Thaw a frozen hose (30–60 minutes)

Washers in unheated garages or basements can freeze in winter. LG’s steps:

  1. Disconnect the supply hose and check whether water comes out of the faucet.
  2. If the faucet is frozen, warm it for about 5 minutes.
  3. Thaw the disconnected hose in warm water no hotter than 50°C (122°F), then reconnect it.

Don’t use boiling water on the hose. If the display shows FF, that’s LG’s separate freeze warning for the inside of the washer.

Fix 5: Check your water pressure (5 minutes)

LG’s top-load list mentions low water pressure as a cause of IE. Open a nearby tap: if the flow is weak there too, the problem is your water supply, not the washer. A partly closed main valve or a house-wide pressure problem needs fixing before the washer will fill normally.

When it’s the water supply valve

If water reaches the washer, the filter is clean and IE still comes back, LG says there may be a malfunction in the water supply valve. That part opens and closes to let water in, and replacing it is a job for a technician.

Still stuck? One more thing to check

LG’s IE guide doesn’t mention it, but a drain hose pushed too deep into the standpipe can siphon water out as fast as it comes in, so the tub never reaches its level. Samsung includes this check in its own fill error steps (its version of IE is 4C). If your LG keeps showing IE with good water flow, check the drain hose too. Our Washer Not Filling guide covers it, with brand-by-brand drain hose limits in the Washer Not Draining guide.

How to prevent IE errors

  • Check the water supply filter once or twice a year, and more often with well water or old pipes.
  • Leave a little room behind the washer so the hose doesn’t get squeezed.
  • Keep a washer in an unheated space from freezing in winter.
  • Open the faucet fully again after any plumbing work.

When to call a technician for an IE error

Call LG support or a local pro if IE keeps coming back after you’ve checked the faucet, the hose, the filter and your water pressure, or if water keeps flowing in when the washer is off.

HomeAdvisor puts a water inlet valve at $95–$190, new hoses at $130–$250 and the average washing machine repair at $125–$450 (updated June 17, 2026). Check the warranty first and have your model number ready.

If the washer is old and the quote is high, our repair or replace guides help you decide.

LG IE error FAQ

What does IE mean on an LG washer?

IE is LG’s water inlet error. On front-loaders, LG says it means the tub didn’t fill to the right level within a set time. On top-loaders, LG describes it as water not reaching the washer, or the water pressure being too low. Older models show it as E02 or E10.

Where is the water inlet filter on an LG washer?

LG says the water supply filter sits at the end of the inlet hose connection. Turn off the faucet, unscrew the hose and pull the filter out with your fingers or pliers to clean it.

Can I fix an LG IE error myself?

Usually, yes. A closed faucet, a bent hose, a clogged filter or a frozen hose cause most IE errors, and all four are free DIY fixes. If those don’t work, LG says the water supply valve may be faulty, which is a job for a technician.

Why does my LG washer show IE in winter?

A frozen supply hose is a common winter cause. LG suggests disconnecting the hose, checking that water flows from the faucet and thawing the hose in warm water no hotter than 50°C (122°F).

How much does it cost to fix an LG IE error?

Most fixes are free. If the water inlet valve has failed, HomeAdvisor puts the repair at $95–$190 (updated June 17, 2026).

Sources