Quick answer
A dishwasher that leaves water in the bottom usually has a clog or a hose problem, not a broken pump. Check the sink and disposal, remove the knockout plug on a new installation, clean the filter, clear the pump area, straighten the drain hose, clean the air gap, and try a forced drain. Most of these cost nothing.
Standing water after a cycle is one of the most common dishwasher complaints, and it is usually fixable at home. The water has nowhere to go because something is blocking the path from the tub to your sink drain. That blockage can be inside the dishwasher, in the hose, or in your plumbing.
This guide follows the troubleshooting pages from Samsung, LG, Whirlpool and Bosch. The brands agree on the main checks, and where a detail applies to one brand only, we say so. If you decide the dishwasher is not worth fixing, our repair or replace guide shows how to compare the costs.
What causes a dishwasher not to drain
Work down this list in order. The first seven cost nothing to check.
| Check order | Cause | Difficulty | Cost |
|---|---|---|---|
| 1 | Clogged sink drain or garbage disposal | Easy | $0 |
| 2 | Knockout plug not removed from a new disposal | Medium | $0; a plumber if you prefer |
| 3 | Dirty or incorrectly installed filter | Easy | $0 |
| 4 | Debris in the sump or around the drain pump | Medium | $0 |
| 5 | Kinked, pinched or sagging drain hose, or no high loop | Easy–Medium | $0 |
| 6 | Dirty air gap | Easy | $0 |
| 7 | Frozen drain line in very cold weather | Easy | $0 |
| 8 | Failed drain pump or control fault | Hard | About $200 typical repair |
The repair figure comes from HomeAdvisor’s dishwasher repair guide. It says a typical repair is about $200 and most jobs fall between $160 and $300. These are national averages and cover every brand.
Samsung notes that a dishwasher that does not drain often has a problem outside the machine, in the sink or the home’s plumbing. That is why the first two fixes are about the sink and the disposal.
8 fixes for a dishwasher that will not drain
Safety first
Turn off the dishwasher’s power at the circuit breaker, not just at the control panel, and shut off the water supply at the valve under the sink. Whirlpool gives this as its first step. Wear gloves, because Samsung and Bosch both warn that debris in the drain area can be sharp. Water in the tub and the hoses may be hot.
Fix 1: Check the sink and the garbage disposal (10 minutes)
Many drain problems start at the sink, not in the dishwasher.
- Run water in the connected sink for about 30 seconds. Samsung says that if the sink does not drain either, the problem is your home’s plumbing and a plumber is the next step.
- If you have a garbage disposal, make sure it is clear of food waste, as Samsung advises. Run it to clear any obstruction.
- If the dishwasher connects directly to the drain, look down the drain for a visible blockage, as Samsung suggests.
- Whirlpool says to check the sink tailpiece, the trap and nearby plumbing for buildup. Clearing a sink blockage often solves the problem.
Fix 2: Remove the knockout plug on a new disposal (15–30 minutes)
Do this check if the dishwasher or the disposal was recently installed or replaced, or if the dishwasher never drained well from the first cycle.
- A new disposal has a plug in the opening where the dishwasher hose connects. LG says that if the disposal is new or this is the first dishwasher connection, the drain opening may still be plugged.
- Whirlpool says a retained plug blocks drainage completely. Samsung says the disposal cap may be the cause of the blockage, and Bosch lists it as a possible cause of its E24 drain code.
- LG says an installer or plumber has to remove the plug, typically with a hammer and screwdriver, and then reattach the hose with its clamp.
- Because this means disconnecting the hose, many people prefer to have a plumber do it.
Fix 3: Clean the filter (15 minutes)
Tools: soft brush, warm water, flashlight.
- Remove the lower rack. LG says to turn the mesh filter counterclockwise to remove it, and Whirlpool says to twist the upper filter counterclockwise and lift it out, taking out the lower filter too if your model has one. The layout differs by model, so check your manual.
- Rinse the filters under warm water and use a soft brush. Whirlpool says to avoid abrasive pads, and Bosch says to scrub with a soft brush and soap under running water.
- Shine a flashlight into the sump and remove any food, seeds, toothpicks or glass. Whirlpool lists these as typical culprits.
- Put the filters back correctly. Whirlpool says to reseat the lower filter flat and turn the upper filter clockwise until it is fully engaged. Samsung says missing or incorrectly inserted parts can cause drain issues and errors.
- Run a short rinse cycle and check whether water remains.
LG says to clean the filter after each load for the best wash performance, and at least once a month in hard-water areas.
Fix 4: Clear the sump and the drain pump (15–30 minutes)
Tools: sponge, flashlight, gloves.
- With the filter out, look at the pump cover underneath. Bosch says to check that the pump cover is not loose. Your owner’s manual shows where it is.
- Bosch says to follow the manual to remove the pump cover, then use a sponge to remove debris and standing water. Wear gloves, because some debris may be sharp.
- Put the pump cover and filter back in place.
- If you hear a steady hum but no water moves, Whirlpool says that suggests a jammed impeller. If you hear nothing at all during a drain, stop and call a technician rather than opening the machine further.
Fix 5: Straighten the drain hose and check the high loop (15 minutes)
- Look under the sink for the drain hose. LG describes it as a ridged hose, usually white, opaque or gray. Make sure nothing is pressing on it or pinching it, and straighten any kinks.
- Samsung says that if the problem started right after installation, check whether the dishwasher is sitting on its own drain hose and pinching it shut.
- The hose needs either an air gap or a high loop, which is part of the hose rising above its connection to the sink. Samsung and Whirlpool both say that without one, water can flow back into the dishwasher. Whirlpool says the high loop should be secured to the underside of the counter.
- For a stubborn clog, Whirlpool says to loosen the clamp, detach the hose from the disposal or the sink tailpiece and flush it with warm water. Use a flexible plastic line or a dishwasher-safe brush, never sharp tools that could puncture the hose.
- Reattach the hose and tighten the clamp snugly, without overtightening.
If the hose is damaged beyond straightening, Samsung says to request service.
Fix 6: Clean the air gap (5 minutes)
Only some sinks have an air gap. It is the small cylinder on the sink or the counter, next to the faucet.
- LG says to turn the dishwasher off with the POWER button, then remove the air gap cover and the plastic cap underneath.
- Clean out any debris with a toothpick or a brush. LG then suggests pouring hot water into the gap with a turkey baster.
- Replace the cap and the cover.
- Whirlpool adds a useful test: if water spills out of the air gap into the sink during a drain, the blockage is farther along, between the hose and the drain.
Fix 7: Force a drain (5 minutes)
LG describes this for its dishwashers. Samsung and Whirlpool do not cover it, so check your manual for other brands.
- If your LG model has a CANCEL & DRAIN option, press and hold the two buttons your manual names. They vary by model.
- If it does not, LG says to start a cycle, let it run for 45 seconds, then power it off. The first 45 seconds of any cycle is drain only.
Fix 8: Rule out frozen lines and run a test cycle (20 minutes)
- In very cold weather, Samsung says to check whether the drain line is frozen. Leave the cabinet door under the sink open, or warm the area. If the lines stay frozen, contact a plumber. Samsung says frozen lines are not covered by warranty service.
- LG says to run a Heavy Duty or Normal cycle with no dishes and no detergent to flush the unit and test the drain.
- Once it drains, clean the filter and the spray arms. LG suggests running an empty cycle with a cup of vinegar or a dishwasher cleaner.
Which fix should you try first?
If you would rather not go in order, match what you see to a starting point.
- It never drained properly since the installation: start with the knockout plug (Fix 2) and the drain hose (Fix 5). The installation is the likely cause.
- It stopped draining suddenly on an old machine: start with the filter (Fix 3), then the sump and pump area (Fix 4).
- The kitchen sink is also slow: the problem is in the plumbing, so start with Fix 1 and call a plumber if the sink does not clear.
- Water spills out of the air gap during a drain: the blockage is downstream, so check the disposal, the sink tailpiece and the hose (Fixes 1 and 5).
- It hums but the water does not move: go straight to the sump and pump area (Fix 4).
- A cold snap just hit: check for a frozen drain line (Fix 8) before you take anything apart.
- A drain code is showing: read the code section below, then work through the fixes in order.
Whichever route you take, finish with a test cycle, so you know the problem is solved before you put the lower rack back and load dishes.
What the water level tells you
Whirlpool’s page does not define a normal level, but it gives these clues.
- Water slightly above the filter screen points to a partial restriction in the filter, the sump or the hose.
- Water near the door opening points to a severe blockage or a pump that is not running.
- A steady hum with no water movement points to a jammed impeller.
Use them to decide where to start, but do not rely on them as proof of the cause.
Drain error codes by brand
Many dishwashers show a code when they cannot drain. The code tells you where to look, and the fixes above cover each one.
- Samsung: its page lists 5C, 5E, OC and OE as drain or overflow errors. It says missing or incorrectly inserted drain parts can cause them.
- LG: OE means the unit detected a drain issue, usually from food clogs or an installation problem. If OE comes back after the steps above, LG says the dishwasher needs repair service.
- Bosch: E24 means the dishwasher is not draining properly because the drain filter is blocked. Bosch lists a blocked drain hose, a dirty filter and an unremoved disposal plug as causes. After fixing the cause, reset the dishwasher and the code as the owner’s manual describes.
Other codes and flashing-light patterns are covered in each brand’s own error code guide.
GE, KitchenAid and other brands
KitchenAid is part of Whirlpool Corporation. KitchenAid’s product help page on a dishwasher that will not drain follows the same order as this guide: turn off power at the breaker, bail out the standing water, clean the filter, then check the drain hose, the high loop or air gap and the sink or disposal connection. It adds two useful clues: a steady hum with no water moving suggests a jammed pump impeller, and water spilling from the air gap means the blockage is further down the hose or sink plumbing. KitchenAid also says not to use drain-opening chemicals inside the dishwasher. For a dishwasher that was just installed, its separate page puts the disposal knockout plug first.
For GE, we did not find an official page on this problem that we could check, so we do not quote GE here. The filter, drain hose, air gap and disposal checks in this guide are not brand-specific and apply to GE dishwashers too. For a GE error code or a replacement part, use the manual for your model number.
A new dishwasher or a new disposal
If the dishwasher has never drained properly, the cause is usually the installation, not a fault in the machine.
- LG says that if the OE error appeared on the first cycle, the hose may be kinked, too high or too long, which the installer should correct. It also says not to add any extension to the drain hose.
- A plugged disposal opening is the other classic cause, covered in Fix 2.
- Samsung recommends professional installation and says local regulations for the drain hose may vary. If you are unsure, ask the installer to check the hose route.
How to keep it draining
- Clean the filter regularly. LG says after each load for the best results, and at least monthly in hard-water areas.
- Scrape large food scraps, seeds and bones off dishes before loading, and keep glass and labels out of the tub.
- Run the garbage disposal before you start the dishwasher, so the shared drain is clear.
- Run a vinegar or dishwasher cleaner cycle from time to time, as LG suggests.
- Use the right filter parts. Missing or wrongly seated parts cause the drain problems and errors that Samsung describes.
When to call a technician for a dishwasher that will not drain
Call the manufacturer or a local pro if the water stays after all eight fixes, if the code comes back, or if you see leaks, burning smells, damaged wiring or a breaker that keeps tripping. Whirlpool tells you to stop and call a technician in those last cases. Bosch and Samsung both direct you to their customer support if the steps do not clear the problem.
HomeAdvisor puts a typical dishwasher repair at about $200, with most jobs between $160 and $300. Before you book, check the warranty and have the model and serial numbers ready. Tell the technician which fixes you already tried and whether the dishwasher drains into a disposal or an air gap.
If the dishwasher is old and the quote is high, our repair or replace guide shows how to decide.
Dishwasher Not Draining FAQ
Why is there standing water in my dishwasher after a cycle?
Something is blocking the drain path. The usual causes are a dirty filter, a kinked hose, a clogged disposal or sink, or a knockout plug that was never removed on a new installation.
Can I run the dishwasher with standing water?
It is better to fix the drain first. Water that cannot leave the tub can overflow, and the water left behind makes a mess and may start to smell.
Where is the filter in a dishwasher?
It sits in the bottom of the tub, under the lower rack. LG, Whirlpool and Bosch all describe turning or lifting it out. The exact design varies by model, so check your manual.
What is the knockout plug in a garbage disposal?
It is a plug in the disposal’s dishwasher connection, left in place until the dishwasher is installed. If it is not removed, Whirlpool says drainage is blocked completely.
How do I force my dishwasher to drain?
LG says to use Cancel & Drain if your model has it, or to start a cycle, wait 45 seconds and power it off. Other brands differ, so check your manual.
Is it worth repairing a dishwasher that will not drain?
Often yes, because most causes are cheap. If a technician says the pump or control board has failed, compare the quote with the price of a new dishwasher using our repair or replace guide.
