Dishwasher Not Cleaning Dishes Properly: 10 Causes

Quick answer

When a dishwasher is not cleaning dishes, the cause is usually a clogged filter, blocked spray arms, water below 120°F, poor loading or the wrong detergent. Clean the filter and spray arms, run the kitchen tap hot before starting, load dirty sides toward the arms and use tablets or packs. Hard water film needs rinse aid.

Pulling out a rack of plates that still have food stuck to them is frustrating, and it feels like a broken machine. It rarely is. In most cases a dishwasher not cleaning dishes is short of one of four things: clean water spray, heat, the right detergent, or room for the water to reach every surface. All four can be checked at home, and most fixes cost nothing.

This guide pulls together what Whirlpool, GE Appliances, Bosch, LG and Samsung say on their own U.S. support pages, in the order that saves you the most time. Where the brands disagree, we show both sides. Our own advice is labeled as ours.

Why your dishwasher is not cleaning dishes: 10 causes

Work down the table. The first causes are the most common and the cheapest to fix.

#CauseWhat you noticeDifficultyTypical cost
1Clogged filterGrit, food specks, bad smell, water left in the bottomEasy$0
2Blocked or stuck spray armsOne rack dirty, the other fine; dirty spots in a patternEasy$0
3Dishes blocking the arms or the detergent doorDetergent still in the dispenser; dirty dishes near tall itemsEasy$0
4Overloading or poor loadingDirty dishes in the middle of the rack, nested bowlsEasy$0
5Water not hot enoughGreasy film, tablets not fully dissolvedEasy$0
6Wrong cycle for the soilBaked-on food survives a light or quick cycleEasy$0
7Wrong or poor detergentFilm, residue, or suds on the floorEasyPrice of new detergent
8Hard water and no rinse aidWhite cloudy film that wipes off with vinegarEasy–MediumRinse aid; a softener costs more
9Water supply valve or pressureLow water in the tub, poor rinsingMedium$0 if the valve was closed
10Failed part (wash pump, heater, inlet valve, dispenser)Quiet cycle, no water movement, cold dishes after dryingHardRepair quote

If the dishwasher also leaves standing water, read our dishwasher not draining guide alongside this one, because a blocked drain and a dirty wash often share a cause.

Safety first

Turn the dishwasher off and let it cool before you reach in: the water, heating element and some racks stay hot after a cycle. Wear gloves around the filter and sump, since broken glass and bones collect there. Switch off the circuit breaker before you remove any lower panel. Never put hand dish soap in the dishwasher: Whirlpool warns that it causes suds.

Fix 1: Clean the filter

A dirty filter is the first thing Bosch, LG and GE point to. The filter sits in the floor of the tub and stops food from being sprayed back onto the dishes. When it clogs, the same dirty water gets recirculated.

  1. Remove the bottom rack.
  2. Twist the filter out according to your manual, usually counterclockwise.
  3. Bosch says to wash it with soap and a soft brush under running water. LG says to rinse it under running water.
  4. Check the opening for bits of glass or bone, then lock the filter back in.

How often? GE says to remove and clean the fine or ultra-fine filters once a month. Our step-by-step guide to cleaning a dishwasher filter shows the Bosch and Samsung designs step by step.

Fix 2: Clear the spray arms

The spray arms are the bars that spin under each rack and throw water at the dishes. If their holes are blocked or they cannot turn, part of the load never gets washed.

  1. Pull out the racks and spin each arm by hand. It should turn freely.
  2. Bosch says to rinse the arms under water to check for blocked holes and use a toothpick to loosen any debris.
  3. GE says to loosen debris in the jets with a paper clip or tweezers, taking care not to damage them.
  4. Most arms unscrew or unclip. Check your manual before forcing anything.

A good test, which is our own: hold a removed arm up to a light. Each hole should show a bright dot. Dark holes are blocked.

Fix 3: Check nothing blocks the arms or the dispenser

Whirlpool and LG both list items that block the spray arms. A tall pan, a cutting board or a pot handle hanging below the rack can stop the arm in its first turn.

  1. After loading, spin each arm by hand. If it hits anything, move the item.
  2. Close the door and open it again. Look at the detergent door: it must be free to swing open.
  3. LG suggests adjusting the rack height if dishes touch the arm.
  4. If you find detergent still in the dispenser after a cycle, the door was blocked or the detergent got wet before the cycle.

Fix 4: Load the dishwasher correctly

Loading is not about neatness. The water must reach every dirty surface.

  • Space: Whirlpool says to leave enough space between items so water and detergent can reach every surface. Bosch says the same.
  • Direction: Whirlpool says to face soiled surfaces down and inward toward the spray arms.
  • Upright and upside down: LG says to stand plates upright, load bowl-shaped items such as cups and pots upside down, and make sure dishes do not overlap.
  • Plastics: Whirlpool says to put plastic cups, bowls and mugs in the third-level rack if your model has one, and never on the lower rack.

Our tip: run one load with the rack only two-thirds full. If everything comes out clean, overloading was the problem.

Fix 5: Make sure the water is hot enough

Detergent needs heat to dissolve and to work. Cold water is one of the most overlooked causes.

  1. GE says the water heater should deliver at least 120°F to the dishwasher. Samsung’s guide to a cycle ending before dishes are clean gives a range of 120 to 149°F.
  2. GE suggests checking by running hot water at the kitchen sink and measuring it with a cooking thermometer.
  3. Run the kitchen tap until it is hot before you start the dishwasher, so the first fill is not cold. This is our own habit.
  4. GE warns against running the dishwasher during or right after a bath or a laundry load that uses hot water.
  5. GE also says to make sure the dishwasher is connected to the hot water line, not the cold.

Do not turn the water heater above the range your heater and household safety allow. Hot tap water can scald.

Fix 6: Choose the right cycle

GE says a short or light cycle used on a heavily soiled load may not clean it, and to select a longer cycle. GE also says to turn on the added heat options if your model has them and to deselect a single-rack zone option if you want both racks washed. Whirlpool suggests the high-temperature option for baked-on food and heavier cycles for heavy soil.

For burnt pans, LG suggests soaking them for an hour and pre-rinsing before loading. For everyday plates, Bosch says there is no need to pre-rinse: just scrape off food, because the detergent needs some soil to work on. The two advise different things for different loads, and both are right: soak the stubborn pan, scrape the normal plate.

Fix 7: Use the right detergent, and the right amount

Detergent is the most common place where small mistakes add up.

  • Format: Whirlpool says pre-measured tablets or packs are better than powder, liquid or gel at reducing film. LG says liquid detergent is not recommended. GE names Cascade Platinum ActionPacs or Finish Quantum.
  • Only dishwasher detergent: Whirlpool and GE both say to use only detergent made for automatic dishwashers. Hand dish soap makes suds; Whirlpool says to turn the dishwasher off and let them dissipate if that happens.
  • Fresh detergent: Whirlpool says to add it right before starting the cycle and to store it sealed in a cool, dry place. Old, clumped powder dissolves poorly.
  • Amount: GE says to adjust the amount to your water hardness. Samsung lists too much detergent as one cause of etching.

Fix 8: Deal with hard water and add rinse aid

A white, cloudy film is usually minerals from hard water, not food. Samsung gives a simple test: wipe a filmy glass with lemon juice or white vinegar. If the film comes off, it is hard water. If it stays, the glass is probably etched, which is permanent.

  1. Use rinse aid. Whirlpool and Bosch both say to add it. Samsung says its dishwashers are designed to be used with rinse aid to reduce hard-water film.
  2. Consider a softener. Whirlpool says water at 15 grains per U.S. gallon or more can damage the dishwasher and hurt results, and recommends a water softener. Samsung says not to soften below 7 grains per gallon.
  3. Clean out the deposits. Whirlpool suggests a dishwasher cleaner or a white vinegar rinse. Samsung suggests a cup of white vinegar on the upper rack in a hot cycle about once a month, or the Self Clean cycle on models that have it.

Your local water utility usually publishes the hardness of your water. Test strips from a hardware store are an alternative.

Fix 9: Check the water supply and pressure

If the tub does not fill properly, the arms cannot spray hard enough.

  1. Whirlpool says the water supply valve, usually under the sink, must be completely open.
  2. Whirlpool and GE both give a water pressure range of 20 to 120 psi.
  3. Whirlpool also notes that a flood-prevention device installed on the supply can block water flow if it is fitted incorrectly.
  4. GE says the drain hose should not rise above 36 inches, and that the dishwasher should be level, because poor draining also hurts washing.

Fix 10: When a part has failed

If you have done all of the above and the dishwasher still runs quietly, leaves dishes untouched or does not heat, a part may have failed. Common candidates are the wash pump motor, the heating element, the water inlet valve and the detergent dispenser. These need a technician or a careful repair by someone experienced; turn off the power at the breaker before any panel comes off.

LG says that if the problem continues after cleaning, service is required. GE offers a repair booking, and Bosch lists its customer support line, 1-800-944-2904.

Before you pay, weigh the repair against the age of the dishwasher. The NAHB study puts the average dishwasher life at about 9 years, and our repair or replace guide shows how to apply the 50% rule to a quote.

Why are top-rack dishes not clean?

When only one rack is dirty, the problem is almost always that rack’s spray arm or its water supply.

  • The upper arm is often fed through a tube at the back. If the upper rack sits crooked, the connection may not line up. Push the rack fully in and check it rolls straight (our tip).
  • Check that tall items in the lower rack do not stop the upper arm.
  • GE notes that a zone or single-rack option washes only one rack. Make sure it is off.
  • Clean the upper arm’s holes the same way as in Fix 2.

Why is the dishwasher getting worse, even on heavy wash?

A machine that cleaned well last year and now leaves film or specks is usually collecting dirt inside: a filter that has never been cleaned, scale in the spray arms, or grease in the sump. A heavy cycle cannot fix a dirty machine.

  1. Clean the filter (Fix 1) and spray arms (Fix 2).
  2. Run a cleaning cycle. LG describes removing the filter, rinsing it, putting 40 g of citric acid in the detergent dispenser and running the Tub Clean cycle on its models. Samsung suggests vinegar or the Self Clean cycle.
  3. Check the water temperature again (Fix 5). A water heater that has been turned down for the season is easy to miss.

Film or etching? How to tell

These look similar but need opposite fixes.

Hard-water filmEtching
LookWhite, chalky, cloudyCloudy, sometimes rainbow-colored, rough
Vinegar test (Samsung)Wipes offStays
CausesHard water, no rinse aidToo much detergent, too much heat, or very soft water (Samsung)
FixRinse aid, softener, cleanerLess detergent, water no hotter than needed, avoid over-softening
Reversible?YesNo: the glass surface is damaged

Brand notes

  • Whirlpool, Maytag and KitchenAid: Whirlpool’s page covers the supply valve, flood-prevention devices, loading, tablets and hard water above 15 grains per gallon.
  • GE: GE’s checklist is the most detailed on water: hot water line, at least 120°F, 20 to 120 psi and the 36-inch drain hose limit, plus monthly filter cleaning.
  • Bosch: Bosch starts with the filter, loading, no pre-rinse, rinse aid and spray arms.
  • LG: LG’s cleaning guide focuses on food residue, loading, spray arm clearance, high-performance detergent and the Tub Clean cycle with citric acid.
  • Samsung: Samsung’s guide focuses on error codes, hard water versus etching, rinse aid and water between 120 and 149°F.

Other brands follow the same principles. The steps above are safe for any standard dishwasher, but check your manual for filter and arm removal.

How to keep your dishwasher cleaning well

  • Scrape plates, do not rinse them (Bosch).
  • Clean the filter once a month (GE).
  • Keep rinse aid topped up (Whirlpool, Bosch, Samsung).
  • Run a vinegar or cleaner cycle about once a month if you have hard water (Samsung).
  • Check the spray arms every few months (our suggestion).
  • Use fresh tablets or packs stored in a dry place (Whirlpool).

The same small, regular cleaning keeps other machines working too; our front load washer cleaning guide applies the idea to the washer’s filter and seal.

Keep a log for one week: the cycle you used, how full the racks were, and whether the dishes came out clean. Patterns show up fast, such as only the Quick cycle failing or only full loads failing. That tells you whether to fix heat, loading or the machine. This is our own method.

Dishes Still Dirty? FAQ

Why is my dishwasher running but not cleaning?

The motor can run while the water does little. A clogged filter, blocked spray arms, a closed supply valve or cold water are the usual reasons. Clean the filter and arms, open the valve fully and check the tap reaches 120°F (GE).

Why are my dishes still dirty after a cycle?

Most often the load blocked the spray, the cycle was too light or the detergent did not dissolve. Load dirty sides toward the arms, choose a heavier cycle for baked-on food and use tablets or packs (Whirlpool).

Why are top-rack dishes not clean?

The upper spray arm may be blocked, stopped by a tall item below, or not connected because the rack is crooked. Check that a single-rack zone option is off, as GE notes.

Why does my dishwasher clean worse even on heavy wash?

The machine itself is likely dirty, or the water is not hot enough. Clean the filter and arms, run a cleaning cycle with vinegar or citric acid as Samsung and LG suggest, and recheck the water temperature.

Should I rinse dishes before putting them in the dishwasher?

Bosch says there is no need to pre-rinse: scrape off food instead. LG suggests soaking and pre-rinsing only burnt pots or baked-on egg.

What causes a white film on dishes?

Usually hard water. Samsung says film that wipes off with vinegar or lemon juice is hard water; if it stays, the glass is etched. Rinse aid and, for very hard water, a softener help (Whirlpool).

Sources