How to Clean Refrigerator Condenser Coils

Quick answer

To clean refrigerator condenser coils, unplug the fridge, find the coils (behind the bottom grille, on the back or on top), brush off the dust with a coil brush and vacuum it up. Replace the grille and plug it back in. LG says once or twice a year; many newer models never need it.

The condenser coils release the heat that the refrigerator pulls out of your food. When they are covered in dust and pet hair, that heat has nowhere to go, so the compressor runs longer. Learning how to clean refrigerator condenser coils takes about twenty minutes and a brush. First, though, check whether your model needs it at all.

Does your refrigerator need coil cleaning?

Not every fridge does. GE Appliances says most of its refrigerators made since 2001 have a NeverClean condenser, with the coils inside the compressor housing where they stay clean. Whirlpool says some models do not need cleaning and others can only be cleaned by a certified technician. Your owner’s manual tells you which type you have.

What you need

ItemWhy
Refrigerator coil brushLong, thin bristles reach between the coils. GE sells part PM14X51; Whirlpool sells 4210463RW
Vacuum with a crevice or brush toolPicks up the dust you loosen
Safety glasses and glovesWhirlpool advises glasses; GE warns that top-mounted fins have sharp edges
FlashlightThe space under the fridge is dark

Safety first

Unplug the refrigerator or switch off its circuit breaker before you start, as both Whirlpool and GE instruct. Whirlpool says not to disturb the water lines for the ice maker or dispenser, and not to bend the fins or tubing. When you pull a fridge out, GE warns not to run over the power cord or tubing.

Where are refrigerator coils?

GE lists three locations:

  • Bottom, behind the base grille at the front. This is the most common on modern fridges.
  • Back, on the outside of the rear panel. Common on older and simpler top-freezer models.
  • Top, behind a grille above the doors, on many built-in models.

How to clean refrigerator condenser coils, step by step

Coils at the bottom

  1. Unplug the refrigerator.
  2. Remove the base grille. Whirlpool says to open both doors, then push the top of the grille in while pulling the bottom up. Other models unscrew or pull straight off.
  3. Brush the coils. Slide the coil brush in and work it gently front to back. Whirlpool says to vacuum the grille, the open area behind it and the front of the coils.
  4. Vacuum the floor in front of and under the fridge. GE says to sweep or vacuum the debris.
  5. Reattach the grille. Whirlpool says to line up the support tabs with the metal clips and push until it snaps in.
  6. Plug it back in.

Coils on the back

  1. Unplug and pull the refrigerator away from the wall, watching the cord and water line.
  2. Brush the coils from top to bottom, then vacuum the coils and the floor.
  3. Push the fridge back carefully and plug it in.

Coils on top

  1. Turn off the power at the breaker, as GE instructs.
  2. Raise the front grille panel.
  3. Wear long sleeves and gloves. GE says to brush the fins with a soft-bristle brush from the middle toward the right, then vacuum.
  4. Lower the panel and restore power.

How often should you clean refrigerator coils?

The brands give different answers:

  • **LG:** once or twice a year.
  • Whirlpool: routine cleaning is usually not needed in a normal home, but households with pets, heavy kitchen traffic or construction dust should inspect and clean every 3 to 6 months.
  • GE: more often if you have pets that shed or the fridge sits somewhere dusty, such as a garage.

Our suggestion: look at the coils every six months with a flashlight and clean them when you see a gray layer of dust.

What happens if you don’t clean them?

Dusty coils make the compressor work harder to get rid of heat. GE lists dirty coils among the causes of a refrigerator not cooling enough, and so do we in our refrigerator not cooling guide. If your fridge feels warm, clean the coils before you call anyone: it is free, and it may be the fix.

Other signs, from our own experience: the fridge runs almost constantly, or the area near the grille feels unusually warm.

Make it part of a routine

Coils are one of several hidden spots that collect dirt. The same twice-a-year session can include the dishwasher filter, covered in our dishwasher filter cleaning guide, and the washer’s seal and drain filter, covered in our front load washer cleaning guide. If your fridge is old and still struggling after a full cleaning, our repair or replace guide helps you weigh a repair quote.

Before you put the grille back, take a phone photo of the coils. Next time, compare the photo with what you see. It shows how fast dust builds up in your home. This is our own habit.

Clean Your Fridge Coils FAQ

Can I use a vacuum to clean refrigerator coils?

Yes. Whirlpool says to use a vacuum with a crevice or brush attachment, or a refrigerator coil brush. Brush first to loosen packed dust, then vacuum it away.

Do I need to unplug the refrigerator to clean the coils?

Yes. Whirlpool and GE both say to unplug the refrigerator or switch off its breaker before cleaning, to reduce the risk of electric shock.

What are the symptoms of dirty condenser coils?

The most common is a fridge that does not cool well or runs nearly all the time. GE lists dirty coils among the causes of a refrigerator not cooling enough.

Do all refrigerators have coils I can clean?

No. GE says most of its models made since 2001 have a NeverClean condenser. Whirlpool says some models need a certified technician. Check your owner’s manual.

Sources