Dryer Won’t Start but Has Power: 7 Checks Before Repair

Quick answer

A dryer that has power but will not start usually has a simple cause: the Start button was not held long enough, the door is not latched, the wrong cycle is set, or a control lock or breaker is the problem. Work through those checks before you pay for a repair.

The light comes on, the display glows, and then nothing happens when you press Start. That feels like a dead motor, but most of the time the dryer is waiting for a condition it does not think has been met. This guide follows the troubleshooting pages from Whirlpool, GE Appliances and LG. They agree on the basics, and where they differ we say so. If your dryer runs but gives no heat, see our dryer not heating guide instead.

Why does my dryer have power but won’t start?

Work down this list in order. Every check from 1 to 6 is free.

Check orderCauseTypical signDifficulty
1Start button not held long enoughDisplay lit, drum silentEasy
2Door not latched, or clothing caughtNo click, no startEasy
3Wrong cycle or control lock onDisplay does not respondEasy
4One of two breakers tripped (electric dryers)Light works, drum will not turnEasy
5“1” or “2” shown on a newer GE display (personality setting)Number on screenEasy
6Loose or burned power cord or terminal block (electric dryers)Intermittent startMedium
7Failed part such as the door switchEverything above checkedHard

7 checks for a dryer that will not start

Safety first

Unplug the dryer before you touch the power cord, the terminal block or any panel. For an electric dryer, also switch off the breaker. These parts carry 240 volts. If you see burned wires or a scorched switch, stop and call a technician.

Check 1: Press and hold Start (1 minute)

Whirlpool says to press and hold Start, Push to Start or Hold to Start for two to five seconds, because a quick tap may not engage the motor. On touch controls, use your fingertip instead of a nail. Dry your hands and wipe the panel, since moisture can stop the controls from responding. GE says to press the Start button all the way in.

Check 2: Latch the door (1 minute)

  1. Push the door firmly until the latch engages. Whirlpool notes that some models have upper and lower latches, and both must be secure.
  2. Look for clothing caught in the door or the latch.
  3. Open the door and inspect the door switch. GE says that a scorched or pushed-in switch may stop the dryer from operating.

A door that will not latch on your washer can cause a similar no-start problem. See our front-load door won’t open guide for how that lock works.

Check 3: Set the right cycle and turn off the control lock (2 minutes)

Whirlpool says to set the Cycle Control to Automatic Dry or Timed Dry, because the dryer will not start on Wrinkle Reduction on some models. If the Controls Locked light is on, press and hold the Cycle Signal button for three seconds. LG says that with Child Lock on, the display will not respond, and you turn it off by holding the CHILD LOCK button for three seconds.

Check 4: Check both breakers (5 minutes)

Whirlpool says electric dryers use two fuses or breakers and gas dryers use one. Make sure they are intact and tight, or reset any that tripped. LG says to turn the breaker off, wait five seconds and turn it back on. If the problem continues, Whirlpool says to call an electrician. GE adds that the dryer should be on its own dedicated circuit.

Check 5: Set the personality on newer GE models (1 minute)

GE says that on 2019 and newer models, a “1” or “2” on the display means the dryer needs its personality set. Press Start to toggle between the two. Choose 1 for electric dryers or 2 for gas dryers.

Check 6: Inspect the cord and terminal block (15 minutes, electric dryers)

With the dryer unplugged, look at the power cord at the back for damage or a loose connection. GE says to check the terminal block as well. If the wires or connections are burned, broken or frayed, replace both. LG gives the same check for the cord and terminal block. See your installation instructions for the cord details.

Check 7: Try LG’s hard reset (LG only, 5 minutes)

LG describes a hard reset for its dryers. Unplug the dryer, hold POWER/START for five seconds, then hold PLAY/PAUSE for five seconds. Plug it back in and try again. If the breaker is off, LG’s version also unplugs the dryer first. Whirlpool and GE do not describe a hard reset on the pages we read, so check your manual for other brands.

Before you call anyone, write down your model and serial number, which Whirlpool says to have ready, and note what happens when you press Start: a click, a hum, a flashing display or nothing. A clear description helps a technician diagnose the problem faster. This is our own tip.

What if the drum light works but the dryer still won’t start?

LG says that if the drum light is on but the dryer will not power on, it needs repair. LG also lists these reasons to call service: the dryer still will not power on after a hard reset, or the processing window flashes a time countdown when you press Start.

Whirlpool and GE point to the owner’s manual and to scheduled service when the basic checks fail. Neither page covers testing a thermal fuse, so we cannot give brand-backed steps for that test here. Our dryer not heating guide covers airflow problems that can cause a dryer to shut down.

If a technician says the motor or control board has failed on an older dryer, compare the quote with a new one using our repair or replace guide. We could not verify a repair cost, because HomeAdvisor blocks automated checks, so ask for a written quote.

Dryer Won’t Start but Has Power FAQ

Why does my dryer have power but won’t start?

Most often the Start button was not held long enough, the door is not latched, a control lock is on, or one breaker has tripped. Whirlpool says to hold Start for two to five seconds and check both breakers.

Is there a reset button on a dryer?

Not on every model. LG describes a hard reset: unplug the dryer, hold POWER/START for five seconds, then PLAY/PAUSE for five seconds. Whirlpool and GE do not describe one on the pages we read.

Does unplugging a dryer reset it?

The pages we read do not say that unplugging alone resets a dryer. LG’s reset combines unplugging with a button sequence. For other brands, check your owner’s manual.

Why does my dryer ignore the Start button?

Control lock or Child Lock may be on. LG says to hold CHILD LOCK for three seconds, and Whirlpool says to hold Cycle Signal for three seconds when the Controls Locked light is on.

When should I call a technician?

Call if the drum light is on but the dryer will not power up, or if checks and a reset do not help, as LG advises. Call an electrician if breakers keep tripping, per Whirlpool.

Sources