Quick answer
A washer that won’t spin usually has an unbalanced load, water that didn’t drain, or a lid or door that isn’t locking. Spread the laundry evenly and run a Rinse & Spin. Still stuck? Check the drain, the level and the lid lock before suspecting the belt or motor.
This guide works for front-load and top-load washers from any brand, including Samsung, LG, Whirlpool, GE and Maytag. It follows the troubleshooting guides published by LG, Samsung and Whirlpool, and it lists the nine causes in the order you should check them: the free fixes first, the repairs last.
If your washer is showing an error code, start there. The code tells you which system tripped. Samsung owners can look it up in our Samsung washer error codes list.
Read the clues first
How the washer behaves narrows the cause down fast. Find your symptom, then jump to that cause.
| What you see | Most likely cause | Check |
|---|---|---|
| An error code on the display | The washer detected a specific fault | Look up the code |
| Clothes soaking wet and water left in the drum | The washer can’t drain | Cause 3 |
| Drum starts to spin, stops and tries again | Unbalanced load or washer not level | Causes 1, 2 and 5 |
| Lid or door won’t lock, or the lock light blinks | Lid or door lock | Cause 4 |
| Spins, but slowly, and clothes stay damp | Load size, cycle or spin setting | Causes 2 and 6 |
| Lots of foam in the drum | Too much detergent | Cause 7 |
| Motor hums but the drum doesn’t turn | Belt, coupling or motor | Causes 8 and 9 |
Safety first
Unplug the washer before you touch anything inside it, open a filter or move it. Never reach into a drum that’s still turning, and wait for the lid or door to unlock on its own. A washer full of water is heavy, so drain it before you tilt or move it, and get a second person to help.
9 reasons your washer won’t spin (and how to fix each one)
1. The load is unbalanced
Difficulty: easy · Cost: $0
This is the number one cause. When laundry bunches on one side of the drum, the washer senses the imbalance and stops the spin to protect itself. LG notes that laundry can tangle together on one side, and Samsung shows it as a UB or UE error.
- Pause the cycle and wait for the lid or door to unlock.
- Untangle the laundry and spread it evenly around the drum. Pull sheets and blankets apart, because they tangle when wet.
- Check the drum for coins, zippers or buttons. LG warns that trapped objects can affect operation.
- Close the lid or door and resume the cycle.
Samsung owners: our Samsung Washer UB Error guide covers this step by step, including calibration.
2. The load is too small, too big or too heavy
Difficulty: easy · Cost: $0
Load size matters more than most people think. Samsung defines a small load as 3–5 pounds (about 1/3 full) and a large load as 6–16 pounds (about 3/4 full), and one pair of jeans weighs roughly a pound. Very small loads clump on one side. Overloaded drums can’t redistribute. A single heavy item, like a bath mat or a soaked comforter, throws the whole drum off.
- Add a few towels to a small load, or lower the spin speed.
- Take out part of an overloaded drum and wash it separately.
- Wash a single bulky item with two or three towels to balance it.
3. Water didn’t drain
Difficulty: easy to medium · Cost: $0, or $300–$400 for a drain pump
A washer won’t spin a drum full of water. Whirlpool’s troubleshooting lists a clogged drain filter, a twisted drain hose or a faulty drain pump as causes of a no-spin. If the clothes are soaking and there’s water in the drum, this is your problem.
- Unplug the washer and check that the drain hose isn’t kinked, crushed or pushed too far into the standpipe.
- On a front-loader, drain the water through the small emergency hose behind the access door at the bottom front, then clean the drain pump filter.
- Run water into the standpipe. If it backs up, the clog is in your house drain, not the washer.
- Run a Rinse & Spin cycle and listen. A pump that hums without moving water is blocked or failed.
For the full steps, with drain hose measurements, see our Samsung Washer 5C Error guide. Most of it applies to any brand. For every brand, see our Washer Not Draining guide.
4. The lid or door isn’t locking
Difficulty: easy to hard · Cost: $0, or $150–$400 for a door lock
Modern washers lock the lid or door before they spin. Whirlpool explains that on its top-load HE washers the lid stays locked while the tub moves, because the tub can spin at very high speeds. Some models won’t even fill with the lid open, and others fill but won’t advance until it’s closed. If the lock can’t engage, the washer won’t spin. Steps from Whirlpool’s lid lock guide:
- Close the lid or door firmly. Check that no clothing is caught in it.
- Remove any debris around the lock and the strike, and clean the area with a damp cloth.
- Do a power cycle: Whirlpool says to unplug the washer for 5 minutes, then plug it back in.
- If the lock still won’t engage, or it clicks without locking, the lock assembly may need replacing.
5. The washer isn’t level
Difficulty: easy · Cost: $0
A washer that rocks on its feet senses movement during the spin and cuts it short. LG suggests pressing on diagonal corners: if the washer shakes, adjust the legs on that side. Samsung recommends leaving about 1 inch between the washer, the dryer and any wall. If it shakes hard or walks across the floor, see our guide to a washing machine shaking violently.
- Rock the washer at each corner to find the one that wobbles.
- Shorten the other legs first, and lengthen the wobbly one only if you have to. Keep all four feet on the floor and the legs as short as you can.
- On front-loaders, loosen the locking nuts before you turn the legs and tighten them afterwards.
- Run a short cycle and check that the washer no longer shakes.
6. The cycle or spin setting is wrong
Difficulty: easy · Cost: $0
Delicate, Hand Wash and Wool cycles spin slowly on purpose, and many washers let you set the spin speed to low or turn it off. Samsung notes that using the wrong cycle can cause errors and poor spinning. Check the spin option on the control panel, pick a normal cycle and try again.
7. Too many suds
Difficulty: easy · Cost: $0
Too much detergent, or regular detergent in a high-efficiency washer, makes foam that slows or stops the spin. Samsung’s error code list describes a suds code (SUd) that pauses the washer until the suds settle, and puts it down to how the detergent is used.
- Run a rinse cycle with no detergent until the foam is gone.
- Use less detergent next time, and use HE detergent if your washer is marked HE.
8. Worn drive belt or broken motor coupling
Difficulty: medium to hard · Cost: varies by model
Not every washer has a belt. Many direct-drive top-loaders use a motor coupling instead. The Home Depot’s Whirlpool troubleshooting guide calls a faulty drive belt one of the most common reasons a Whirlpool washer won’t spin, and says to replace the motor coupling if it’s broken. Typical signs: the motor runs or hums, but the drum barely moves, and you may smell burning rubber.
Replacing a belt or coupling is a common DIY repair on many models, but it means opening the cabinet. Check your model’s service manual first, or have a technician do it.
9. Motor, control board or other electrical fault
Difficulty: hard · Cost: $320–$400 for a motor
If none of the above explains it, the fault is likely electrical. Whirlpool’s guidance says to replace the drive motor if it has power and hums but doesn’t turn, and to check the motor control board for burned components. LG’s advice for a drum that still won’t spin after its basic checks is to request service. This one is for a technician.
Front-load vs top-load: what changes
The causes are the same, but where you look differs:
| Check | Front-load washer | Top-load washer |
|---|---|---|
| Lock | Door lock on the door frame | Lid lock (HE models) or lid switch |
| Drain filter | Usually behind a small door at the bottom front | Samsung says its top-loaders have no removable pump filter; check your manual for other brands |
| Getting the water out | Emergency drain hose behind the filter door | Lower the drain hose into a bucket on the floor |
| Leveling | Adjustable legs with locking nuts | Adjustable legs; see your manual for the leveling steps |
Quick notes by brand
- Samsung: a stopped spin usually shows as UB, UE or Ur. Samsung’s fix list ends with a calibration mode (Cb) that resets weight sensing. Details in our UB guide, and the power reset in our reset guide.
- LG: LG points to the display first (codes such as UE, OE and LE) and suggests a Rinse & Spin test cycle to isolate the problem. If the drum still won’t spin after its checks, LG says service is needed.
- Whirlpool and Maytag: on top-load HE models, check the lid lock first, and power-cycle the washer for 5 minutes as Whirlpool suggests. On older belt-driven or direct-drive models, the belt or motor coupling is a common culprit.
How to prevent spin problems
- Mix large and small items in every load, and don’t spin a single heavy item on its own.
- Stay within your washer’s load sizes. Overloading and tiny loads both cause trouble.
- Empty pockets before you wash. Coins and hair ties end up in the drain pump.
- Clean the drain pump filter regularly if your washer has one.
- Use the right amount of detergent, and HE detergent in HE washers.
- Check that the washer is level again any time it’s moved.
When to call a technician
Call a technician if the washer still won’t spin after you’ve balanced the load, drained it, checked the lock and leveled it. Also call if the motor hums without turning, you smell burning, or you hear grinding or banging during the spin.
HomeAdvisor puts the average washing machine repair at $125–$450, a drain pump at $300–$400, a door lock at $150–$400, shock absorbers or bearings at $150–$200 and a motor at $320–$400 (updated June 17, 2026). Check the warranty first and have your model number ready.
If the washer is old and the quote is high, our repair or replace guides help you decide.
Washer won’t spin FAQ
Why does my washer drain but not spin?
If the water drains but the drum won’t turn, look at the lid or door lock, an unbalanced load, and on belt-driven models the drive belt or motor coupling. A motor that hums without turning points to a motor or control fault.
Why does my washer spin but the clothes are still soaking wet?
The spin was probably cut short or too slow. Common reasons are a small or unbalanced load, a low or No Spin setting, overloading, or water that drained too slowly. Fix those first, then run a Rinse & Spin cycle.
Can an unbalanced load stop a washer from spinning?
Yes. LG and Samsung both list an unbalanced load as a main reason the drum stops spinning. The washer cuts the spin to protect itself. Spread the laundry evenly and restart.
How do I make my washer spin without washing again?
Run a spin-only or Rinse & Spin cycle. LG recommends it as a test: if the drum spins with a smaller, balanced load, the problem was the load, not the machine.
Is it worth fixing a washer that won’t spin?
Usually, if the cause is one of the free fixes or a worn belt or coupling. A motor runs about $320–$400 according to HomeAdvisor, so on an older washer compare that with the price of a new one first.
