Washer Making Loud Noise When Spinning: What It Means

Quick answer

A washer making loud noise when spinning usually has a thump from an uneven load, a rattle from something loose, or a squeal from an overloaded drum. Match the sound to the table below, then check the load, loose objects, shipping bolts, level and hoses. Some sounds are normal.

A washer making loud noise when spinning is alarming, but the sound itself tells you where to look. A rhythmic thump points to the load. A rattle points to something loose. A grinding or squealing sound is the one most likely to need service. This guide helps you tell them apart before you pay for a repair.

It follows Samsung’s noise guide, LG’s page on pounding or rattling during the spin and Whirlpool’s pages on banging noises and clunking during the spin. If the washer also shakes or walks across the floor, see our guide to a washing machine shaking violently.

What each sound usually means

Find your sound, then use the fix that matches it.

SoundLikely causeDifficultyCost
Thumping or knocking in rhythm with the spinUnbalanced load, unlevel washer, or front load shipping bolts still inEasy$0
Rattling or clickingLoose objects in the drum, or the cord or a hose hitting the cabinetEasy$0
Squealing, squeaking or grindingOverloading, usuallyEasy$0
Grating or grinding that comes and goesDebris at the drain pumpEasy–Medium$0
Loud humming or buzzingThe water supply valve is closedEasy$0
A “jet engine” soundToo much detergent, or non-HE detergentEasy$0
A noise that stays with an empty drumA fault inside the washerHard$125–$450 average repair

The repair figure comes from HomeAdvisor’s washing machine repair guide (updated June 17, 2026) and is a national average for all brands.

Noises that are normal

Not every sound is a problem. Samsung and Whirlpool both describe sounds you can ignore.

  • A click followed by a short thump: Samsung says this is the motor clutch switching modes, fades after a moment, and needs no service.
  • A clunk when the washer changes mode: Whirlpool says there is a clunk as the drive system shifts from agitation to spin, or back, and calls it expected.
  • Clicking at the start and end of a cycle: Samsung says some clicking is normal.
  • A quiet hum or buzz while draining: Samsung says this is most common during draining, louder when air mixes in near the end, and louder on a spin-only cycle.
  • A pop, honk or beep when filling starts: Samsung says that is the water inlet valve opening.
  • A clank when you turn the drum by hand: Samsung says this is normal and comes from steel balls in its VRT system.

6 fixes for a washer making loud noise when spinning

Safety first

Stop the cycle and unplug the washer before you reach into the drum or behind the machine. A drum that is still spinning can injure you, and the water inside may be hot.

Fix 1: Rebalance the load (5 minutes)

  1. LG says to press Pause and spread the laundry evenly. Laundry stuck to one side of the tub causes a pounding or rattling noise.
  2. Whirlpool says that when clothes are unevenly distributed, the washer struggles to keep its balance during the spin and can bang. Mix heavy and light items and avoid overloading.
  3. LG says rugs, blankets, mats and waterproof fabrics can make the tub lopsided and prolong the spin.
  4. LG suggests filling the tub to about two thirds of its capacity.

Fix 2: Check for loose objects (5 minutes)

  1. Empty the drum and check the pockets of everything you are about to wash. Whirlpool says coins, buttons and other small items can cause a rattle or a clunk.
  2. LG says to rotate the drum by hand with the clothes removed. On a top loader, a coin or a steel wire can be stuck in the tub, and you can remove it with a tool.
  3. Run a short spin and listen again.

Fix 3: Check the shipping bolts on a front loader (15 minutes)

  1. Samsung says to push the drum through the door. It should bounce slightly. If it feels rigid, the shipping bolts are still in.
  2. Whirlpool says to remove all four shipping bolts and the four plastic spacers from the rear of the washer. Leaving them in can cause noise, vibration or error codes.
  3. Our guide to a washing machine shaking violently has the full steps.

Fix 4: Level the washer (15 minutes)

  1. LG says to push the washer forward, backward and sideways. If it shakes, adjust the legs.
  2. Samsung lists an unlevel washer as a cause of thumping and of rattling.

Fix 5: Check the hoses and anything touching the cabinet (10 minutes)

  1. Whirlpool says water flow and vibration can push the drain or inlet hoses against the back of the cabinet. Secure them with the strap supplied on some models or with a wire tie.
  2. Whirlpool also says brooms, dustpans, dryer racks and hangers leaning on the washer can rattle, especially at high spin speeds.
  3. Samsung adds that the power cord or the drain hose can hit the washer and make a rattling or clicking sound.

Fix 6: Test with a known load, then clean the pump filter (30 minutes)

  1. For a squeal, grinding or squeak, Samsung says to stop the cycle and reduce the load, because it is usually overloading.
  2. To test, Samsung says to run a cycle with about four soaking wet bath towels or a similar weight. If the noise returns, request service. If it does not, you were overloading.
  3. If you hear a grating or grinding noise every cycle, Samsung says to clean the pump filter. See our guide to a washer leaking from the bottom for the steps.
  4. If you hear a loud hum or buzz, Samsung says to check that the home’s water supply valve is open.

When to call a technician for a loud spin

Call the manufacturer or a local pro if the noise continues after you balance the load, remove loose objects, check the bolts, level the washer and secure the hoses. LG says that if the noise persists after you rotate the drum by hand with the clothes removed, a front loader needs repair. Samsung says to request service if the noise continues throughout the cycle. Whirlpool says to contact it or schedule service.

HomeAdvisor puts the average washing machine repair at $125–$450 (updated June 17, 2026). Check the warranty first and describe the sound to the technician. If the washer is old and the quote is high, our repair or replace guide can help.

Washer Making Loud Noise When Spinning FAQ

Why is my washer so loud when it spins?

Most often the load is uneven, something is loose, the washer is not level, or the shipping bolts are still in on a front loader. Rebalance the load and check those items in turn.

Is a banging noise during the spin normal?

A brief bang or clunk when the washer changes mode or balances the load can be normal. A constant, heavy banging is not, and it points to the load, the level or loose parts.

What does a grinding noise mean?

Samsung says squealing, squeaking or grinding is usually overloading. If it comes and goes in every cycle, it can be debris at the drain pump.

Sources